Muff's Modules & More

en. · Posted: Fri Jan 27, 2012 3:23 pm Post subject:

after 4 months of discouragement we finally found out what was the problem with our vco... the ferrites!!! wrong ones? i don't know they simply let only negative voltages pass
now the oscillator is working great! we (my brother, tbh) built 2, i already love them: the skew, the way they fm... and... everything!
now it's time to find out how to make a good panel! confused

thank yuo thomas henry!
thank you wigglers!
thank you matthias!!!
thumbs up

fonik · Posted: Fri Jan 27, 2012 4:52 pm Post subject:

en. · Posted: Fri Jan 27, 2012 8:35 pm Post subject:

frozenkore · Posted: Mon Feb 13, 2012 9:20 am Post subject:

Hey guys, I have a question regarding the PW pot. Given a 300 degree turn pot in your standard ~7 o'clock to 5 o'clock travel, between 7 and say 9, and between 3 and 5, the PW is 0% or 100%. I don't seem to get the full travel out of my pot, though it does seem to stay centered around 12 o'clock. Is this expected behavior? Other than that I just have to get this thing to track Russian Roulette

.

Thanks!
Brian

fonik · Posted: Mon Feb 13, 2012 9:54 am Post subject:

mmmh, will have to check this on my builds.
maybe R52 is a little bit on the low end; just try a slightly higher value (replace with a trimmer or add a 2nd resistor in series).

frozenkore · Posted: Mon Feb 13, 2012 11:09 am Post subject:

Thanks, I'll check to make sure I didn't make some dumb mistake (i.e., 33k instead of 330k). If not, I'll try another value or additional in series.

fonik · Posted: Mon Feb 13, 2012 1:39 pm Post subject:

if it would be easier for you, you could add resistors in series to each end of the pot (between the pot and the suply rail) to find the exact full range.

falafelbiels · Posted: Mon Feb 13, 2012 1:49 pm Post subject:

So is it Fonitronik or Foniktronik?

fonik · Posted: Mon Feb 13, 2012 5:30 pm Post subject:

f o n i t r o n i k
it is a name i got from scott stites hihi

gossip: when i started in the forums i thought i needed a nick name - nobody seemed to use their real names. so i decided to go with fonik, which has been the name of the music project i had at this time meh

sicpaul · Posted: Wed Feb 15, 2012 11:59 am Post subject:

yes, yes, yes - what a great sound love

awsome circuit design (thanx thomas)
great work matthias thumbs up

i love small PCBs (doepfer format)

but ... my timing is so miserable cry

(that's propably why I use sequencers) ....

i'd love to get 4 core boards (or more) and 2 shapers.

any chance to get a second run?
applause

regards t.paul

falafelbiels · Posted: Wed Feb 15, 2012 1:23 pm Post subject:

fonik · Posted: Fri Mar 09, 2012 7:10 am Post subject:

i just wanted to let you know that i re-ordered a few more of PCBs for this VCO. due to the low order quantity i had to raise the prices.

the PRICES (revised for low quantity re-order)
7.- EUR/10.-USD for the VCO core PCB (saw/tri)
and
5.- EUR/7.-USD for the waveshaper PCB (tri2sin/pulse/PWM)

+ p/p
Deutschland: 1.- EUR/2 PCBs, 1.50 EUR/3+ PCBs
Europe: 2.- EUR/2 PCBs, 4.- EUR/3+ PCBs
Outside Europe: 4.- USD/2 PCBs, 6.- USD/3+ PCBs

Isaiah · Posted: Fri Mar 09, 2012 8:01 am Post subject:

Could the Waveshaper PCBs be stacked with the VCO Core PCBs?
It looks like the mounting holes on both PCBs line up, but I'd like to know for certain...

fonik · Posted: Fri Mar 09, 2012 8:36 am Post subject:

yes. they could be mounted back to back. i even mirrored the power connectors and the tri/saw header so that they align.

Paradigm X · Posted: Fri Mar 09, 2012 8:55 am Post subject:

I posted in your other thread but ignore that, and one of each for me please.

sicpaul · Posted: Fri Mar 09, 2012 9:06 am Post subject:

Hi Matthias,

good news nanners

OK I will definitly take 6 cores and 3 shapers.

Do you accept paypal or do you prefer direct "Ueberweisung"?
(sorry my finacial vocabulary is too short)

I might be out of net connection during this weekend and I do not want to miss the pcbs again (this as excusion for my next question - I'm so new to this forum):

Do I get an email for details or do I have to order somewhere else?

PS:
I love your projects and your videos

best regards
(sic)paul

clarke68 · Posted: Fri Mar 09, 2012 9:09 am Post subject:

Dego · Posted: Fri Mar 09, 2012 9:28 am Post subject:

Yes Clarke panel!

regenbot · Posted: Fri Mar 09, 2012 9:31 am Post subject:

i have two of these great oscs, but if Clarke does panel for this i just have to get two more It's peanut butter jelly time!