MUFF WIGGLER Forum Index
 FAQ & Terms of UseFAQ & Terms Of Use   Wiggler RadioMW Radio   Muff Wiggler TwitterTwitter   Support the site @ PatreonPatreon 
 SearchSearch   RegisterSign up   Log inLog in 
WIGGLING 'LITE' IN GUEST MODE

DIY kits for E560 Deflector Shield and E580 Mini-Delay
MUFF WIGGLER Forum Index -> Music Tech DIY  
Author DIY kits for E560 Deflector Shield and E580 Mini-Delay
paults
I will now accept your PayPal pre-orders for:

a) E560 Deflector Shield (combo Frequency shifter/RM/phase shifter)
b) E580 Resampling Mini-Delay (750ms max delay with Clean/BBD/Tape emulation)

Detailed info can be found at my distributor's pages such as :

http://www.analoguehaven.com/synthesistechnology/

These are 1 pcb board (not 2 stacked as the E340/E350) and the pots are pre-soldered as well.. Also 7 jacks instead of 8. There is one option jumper of value on the E580, that selects feedback from the tap position or the end of delay position. The jumper on the E560 is for factory testing (outputs the carrier wave).

Due to the fact I am packing up and moving (again) this week, these will ship ~ Nov 10th. More likely a bit sooner, will depend mainly on the documentation prep.

Price is $235 US/$260 foreign, **PLEASE** specify MOTM or Euro power cable with the kit(s) desired in the Subject line of the PayPal form. Example: Payment for 1ea E580 DIY + MOTM cable

Paypal address is: synth1@airmail.net and **please** include your ship to address.

I have 16 of each available. First pay, first ship!
qu.one
Hey Paul... Price is the same for both kits? Sorry if that's a dumb question but a completed 580 is only $75 more, whereas the 560 is $150 more.
paults
Same price for both.
Paradigm X
Erm, sorry if this is a stupid question, but what does the kit contain?

Or to put it another way, what else do we need to buy (faceplate, jacks/bananas, pots etc?)

Man y thanks
Orbless
Which jacks are the outputs on the 560?
Are the 'audio up' & 'audio down' outputs or are they cv inputs?
Is the 'mix' jack a cv in for the 'wet/dry' or is it an output?
The information on analoguehaven is vague and I am not familiar with euro layouts.
arrmcbain
Money sent for E560 SlayerBadger!
paults
Possibly useful info here:

www.synthtech.com/euro/e560
www.synthtech.com/euro/e580
Orbless
Thanks Paul, I am trying to figure out a 1U MOTM sized panel, so not knowing which were the ins/outs was derailing me.
davebr
I just finished building a 5U version of the E580 Sampling Mini-Delay. I incorporated additional attenuators for audio and the four CV inputs. I have photographs and front panel information on my E580 Module page.

Dave

sduck
Very nice Dave!

I did a video demonstrating using this thing as a flanger - it's the second unit demoed - http://www.youtube.com/watch?v=ZfSpVE5uuNo
paults
BTW: I still have some of these, WITH the pots and switch pre-soldered. And these CAN be removed if you are *careful*. PM if interested. The price is $250 now because of the pots added. Both kits same price.
solaris
these kits can also be adapted for Buchla format:
Drumdrumdrumdrum
If any builders out there want to grab a couple of each for me, I'll be cashed up to buy one of each completed modules by July. seriously, i just don't get it
NS4W
Panels included in the kits?
paults
No panel, knobs or jacks. The pots and switch are pre-soldered, but can be removed if careful.

This is NOT intended to be just a 1:1 kit of the assmebled modules. Rather, it is for "repanel" to MU., Serge, etc

Please note: the price is $235 US/$260 foreign.
davebr
I just finished building a 5U version of the E560 Deflector Shield. I incorporated additional attenuators for audio and the four CV inputs. I reused my E580 panel design and have photos and front panel information on my E560 Module page. This is a very nice module.

Dave

JohnLRice
davebr wrote:
I just finished building a 5U version of the E560 Deflector Shield. I incorporated additional attenuators for audio and the four CV inputs. I reused my E580 panel design and have photos and front panel information on my E560 Module page. This is a very nice module.

Dave

Looks great Dave! thumbs up applause we're not worthy
pugix
Just finished my DIY e580. Used Dave Brown's panel designs. Thanks, Dave!

http://pugix.com/synth/synthesis-technology-e580-sampling-mini-delay/
http://pugix.com/synth/e560-e580-project/

The e560 is almost done, too.
JohnLRice
pugix wrote:
Just finished my DIY e580. Used Dave Brown's panel designs. Thanks, Dave!

http://pugix.com/synth/synthesis-technology-e580-sampling-mini-delay/
http://pugix.com/synth/e560-e580-project/

The e560 is almost done, too.
Nice work, Richard! thumbs up
Cat-A-Tonic
Here are my Frac versions.

mcbinc
Cat-A-Tonic wrote:
Here are my Frac versions.


I love the WWII military styling (hope that's what you were going for).
Cat-A-Tonic
mcbinc wrote:
Cat-A-Tonic wrote:
Here are my Frac versions.


I love the WWII military styling (hope that's what you were going for).

Thanks.

I wasn't aiming for a military aesthetic specifically.

I think this style is utilitarian (for one offs),
and kind of punk because of all the imperfections.
I color code and label in hopes that they are easy to read
and understand the I/O and basic flow.
MUFF WIGGLER Forum Index -> Music Tech DIY  
Page 1 of 1
Powered by phpBB © phpBB Group