Muff's Modules & More

paults · Posted: Fri Jun 15, 2012 9:35 am Post subject:

There is 1 jumper that selects if HOLD/SYNC is for both LFOs or just LFO1. This module uses a lower cost/slower speed/smaller memory DSP/MPU chip. So we crammed it as full as we could. All the functions are there on the front panel but this one option.

This allows the price to drop well below E340/E350 while consuming 1/2 the power.

MR-808 · Posted: Sat Jun 16, 2012 12:52 am Post subject:

Well, here are a couple of tries at a 5U panel:

I'm going to have to mull on this one for awhile. I like the hardware layout, but there's no "obvious" placement for what function goes where. I'm leaning towards the second one.

Back to soldering. ;)

paults · Posted: Sat Jun 16, 2012 9:00 am Post subject:

Must use banana jacks.

Dead Banana

JohnLRice · Posted: Mon Jun 18, 2012 10:19 am Post subject:

Mitchk1989 · Posted: Mon Jun 18, 2012 11:54 am Post subject:

Final price verdict?

paults · Posted: Mon Jun 18, 2012 11:58 am Post subject:

AH was a page up with TBD. Their shipment of E355s leaves here today so I guess in a day or 2 there will be one.

mrcharles · Posted: Mon Jun 18, 2012 4:48 pm Post subject:

Howdy...

Is there a resource that illustrates the waveforms/bank for the LFO?

I had found one for the E350 and wondered if a similar chart were available for us who don't have an oscilloscope (yet).

Thanks...

MR-808 · Posted: Mon Jun 18, 2012 5:21 pm Post subject:

paults · Posted: Mon Jun 18, 2012 5:35 pm Post subject:

look here

www.synthtech.com/euro/e355

I'll have to scan a sheet for the E340 the original was on a crashed hard drive.

mangobob · Posted: Mon Jun 18, 2012 6:55 pm Post subject:

TBD? I can afford that.. thumbs up

Drumdrumdrumdrum · Posted: Tue Jun 19, 2012 4:37 am Post subject:

That is very affordable. help

VomitFlowers · Posted: Tue Jun 19, 2012 11:17 am Post subject:

Mine should be arriving today... looking forward to plugging it in.

JohnLRice · Posted: Tue Jun 19, 2012 3:29 pm Post subject:

JohnLRice · Posted: Tue Jun 19, 2012 6:34 pm Post subject:

VomitFlowers · Posted: Tue Jun 19, 2012 7:37 pm Post subject:

decaying.sine · Posted: Tue Jun 19, 2012 7:49 pm Post subject:

Those are nice 5U panels. I like the first one. No particular reason. It just grabs my eye. You might consider moving the switches up just a tiny bit. It looks like they are crowding the jacks. Also, I am not sure if the hole sizes are just "graphic examples" or to spec, but the jacks look too large and the pot hole sizes look smaller than the typical Synth Tech/MOTM hole for spectrol/bourns/BI/TT bushing size. Are these alpha sized?

Of course, that could be completely an optical illusion!

JohnLRice · Posted: Wed Jun 20, 2012 1:52 am Post subject:

ignatius · Posted: Wed Jun 20, 2012 2:03 pm Post subject:

$259. The price is right me thinks.

JohnLRice · Posted: Wed Jun 20, 2012 9:26 pm Post subject:

Can anyone help? I want to buy an E355 ASAP and I can't seem to find someone that has them and will get back to me about them! cry

I talked to Control Mod as soon as they announced they had them in and they said to email them directly and I did and then never got back to me. So I talked to Analog Haven and they said they were getting a bunch in near the beginning of this week. I saw the AH page had been updated with the price but there was no 'add to cart' button. I inquired with an email and while it's only been 24 hours, I'm getting impatient.

Am I on some E355 black list or something? Tinfoil Hat

CTRL · Posted: Wed Jun 20, 2012 9:37 pm Post subject: