Would be greattt
8 voice mod ?

I used a 12V AC-AC 1000ma because I still had one left, but in the mean time I ordered a 15V AC-AC 1000ma wall wart with this one I have no voltage drop though the voltage regulators are getting hot because they have to handle more input voltage than with a 12V wall wart... Everything is working but...

I build the Mfos wallwart PSU on prototype board with tayda parts only As I still had an 12V AC/AC wallwart from 1000ma lying around I tryed and it works ! I'm getting +15.2V and -15.2V... I tested a few module's seperately VCO 1,2 and 3 and the filter and everything is working on first try :party:...

Sorry, some dbl post weirdness 0.09a has the issue? I took down the 0.2 beta version, there is no reason for that to be up Did to see my original post before that mess about setting the CV range after the firmware rollback? Ow okay sorry no the 0,09a is the old version where everything is working b...

Altitude909 wrote: ↑

Mon Jan 06, 2020 6:43 am

Arnoid wrote: ↑

Wed Nov 20, 2019 2:22 pm

Now when I put the new firmware back on midi isn't even working anymore only cv/gate...

You have to set the root key with the midi again

Yes I tryed several times but didn't got midi to work again..

Hmm editing the main post so the beta version is now the current version is a bit easy I guess

If you see my message and previous messages there are still other problems with it...

Something like this


Still awaiting black screws to screw the modules to the wooden case..

Any news on a final firmware version, the old one with the tightness of the beta one would be perfect :hihi: I had to go back to the old firmware because the beta one acted weird. It worked for a while and was tighter then the first one but I also got weird things (sometimes it triggered note's tha...

dKRelease wrote:What are you plans for the case?

I' think something compact as possible in the spirit of this project..

Thinking about a desktop module / skiff thing build out of plywood wrapped in tolex (I still have form another project)

My modules are finished, I used black toggle switch caps from tayda as slider knobs looks great ! A few shots (Still awaiting a case): https://www.muffwiggler.com/forum/userpix2/2107_img_2271_1.jpg https://www.muffwiggler.com/forum/userpix2/2107_capture_1.jpg I build the Mfos wallwart PSU on prototy...

I'm ready populating the pcb's :hihi: next step building a case The 2n4870 had an incorrect footprint attached to it and so the silkscreen on the pcb is back to front (base 1 and base 2 are back to front). There are 2 ways to combat this. Either mount it on the bottom instead (this will result in th...

Any news on a final firmware version, the old one with the tightness of the beta one would be perfect :hihi: I had to go back to the old firmware because the beta one acted weird. It worked for a while and was tighter then the first one but I also got weird things (sometimes it triggered note's that...

Somebody has experience with the rare parts from utsource lately? I recently ordered and received following parts there 2N4392,LM301AN,2N5460,2N5459,2N4870,2N3958,2N3954,CA3046 I'm a bit suspicious about the 2N4392, 2N4870, 2N3958 and 2N3954 They are can type’s but they look brand new... a but weird...

@DKRelease a few questions Do you maybe have schematics of the PSU pcb and overlay in pdf plz ? Think I'm going the same way as I still have a AC/AC adaptor from 15V laying around. All power leads in place ready https://www.muffwiggler.com/forum/userpix2/49470_img_4762_1.jpg Is the flying bus cable ...

I also ordered a pcb/ panel set to get through the winter :hihi: somehow this attracts my attention more than the expensiver TTSH project, I like the compact module approach and I’m also not a fan of the TTSH led sliders so this project seems ideal to build a cheap 2600 clone. The cheap Chinese slid...

thx for your message

I want it to go from very slow to audio rate..

So if I replace C9 with an 10nF Cap I should change R35 to 6.8Kohm if I'm following your theory ? And changing C2, C5 and 6 to 1nF ?

Anybody knows what's the best approach to do the LFO mod on the benderboard of the jupiter 6 to get the LFO in audio range ? I searched the net and found two method's: http://analogue-heaven.1065350.n5.nabble.com/JP-6-LFO-rate-mod-td43837.html#a43839 Replacing C9 (with 10uF cap) and remove C2, C5 an...

Wow Big project though

Maybe this can help, alot of info and panel decals for the enclosure:
https://jup8restoration.wordpress.com/

But only for personal use

...

Also interested in a wooden one if still left.
Sended a PM last week..

A through hole jupiter 8 clone would be great

Is there a protection build in for the power supply ?

I accenditly connected a power supply (with changable connector) with center pin to ground and ring to 12V
But after changing to connector to center pin 12V the syncussion still seems to work

Are these still available ?

Or someone has one for sale

satindas wrote:

Arnoid wrote:Any timing for shipping the next kits ?

I expect to begin shipping the remaining kits on Monday or Tuesday of next week. I’m just waiting for the slider caps which should be here tomorrow; other than that, everything is ready to go

Great

Any timing for shipping the next kits ?