Search found 572 matches

by tubbutec
Wed Apr 01, 2020 7:03 am
Forum: Tubbutec
Topic: DIN MIDI microtonal issue
Replies: 1
Views: 22

Re: DIN MIDI microtonal issue

What is your setting for DIN-Tuning? Sysex, or pitch bend?

What do you mean by 'stop'? Are the gates reacting? Is CV changing?
by tubbutec
Tue Mar 31, 2020 10:03 am
Forum: Eurorack Modules
Topic: µTune - Micro Tonal midi cv converter, quantizer, editor
Replies: 442
Views: 32203

Re: µTune - Micro Tonal midi cv converter, quantizer, editor

Any waveform with only one zero crossing / period is fine. So square, sinr, saw, tri.. are equally ok.
by tubbutec
Tue Mar 31, 2020 8:34 am
Forum: Eurorack Modules
Topic: µTune - Micro Tonal midi cv converter, quantizer, editor
Replies: 442
Views: 32203

Re: µTune - Micro Tonal midi cv converter, quantizer, editor

Currently only one global scale/tuning is supported.
Multiple scales are on the TODO list, but may not become a feature due to hardware limitations.
More likely is a 'multiple scale mask feature'
Basically one tuning, but multiple scales.
by tubbutec
Tue Mar 31, 2020 2:39 am
Forum: Tubbutec
Topic: uTune expander output behaviour
Replies: 1
Views: 30

Re: uTune expander output behaviour

Hi sorry for the late reply. We have much less time for work than usually at the moment, due to the Corona virus situation. The issue is a hardware issue with the plug-in detection. The expander 'thinks' that CV is always plugged in. We recently had a similar issue with an other customer and are now...
by tubbutec
Tue Mar 24, 2020 5:28 am
Forum: Tubbutec
Topic: uTune Expander Plug-in detection issue
Replies: 3
Views: 36

Re: uTune Expander Plug-in detection issue

It looks like there might be an issue with plug-in detection of channel 3. This might be caused by: - You need to use a mono-cable. Otherwise plug-in detection does not work. Make sure you are using a mono, not stereo cable - an actual hardware issue. We have prepared a firmware version that shows t...
by tubbutec
Tue Mar 24, 2020 5:23 am
Forum: Tubbutec
Topic: uTune doesn't output Pitch.
Replies: 3
Views: 175

Re: uTune doesn't output Pitch.

Hi There, Happy you got it working again, a bit confused about which calibration you actually did. The DAC/ADC calibration in expert settings should be fine and not changed. These are calibrated in factory. For HW17 only there is a special case. Here the ADC calibration in the above menu is meaningl...
by tubbutec
Sun Mar 22, 2020 2:50 pm
Forum: Tubbutec
Topic: uTune Expander Plug-in detection issue
Replies: 3
Views: 36

Re: uTune doesn't output Pitch.

Hi,

Can you set channel 3 gate input to 'none' in simple config and report your findings? thank you
by tubbutec
Thu Mar 19, 2020 2:20 am
Forum: Tubbutec
Topic: Unipulse Roland TR-33 and Yamaha MR10 - some trig problems
Replies: 16
Views: 1730

Re: Unipulse Roland TR-33 and Yamaha MR10 - some trig problems

There is now some strong evidence that uniPulse reacts badly to "active sensing" midi messages.
Very likely this is also the cause of your problems.
(MidiOX might not display the active sensing messages due to filtering)

We are currently looking at this and will provide a firmware update
by tubbutec
Tue Mar 17, 2020 7:07 am
Forum: Tubbutec
Topic: KR-55 uniPulse installation questions
Replies: 2
Views: 636

Re: KR-55 uniPulse installation questions

For external MIDI control please follow the attached image: - solder 1 wire to pin 3 of IC 3 (Clock) - solder 1 wire to pin 4 of IC 3 (Reset) - solder both wires to the provided DPDT switch, eg one to each middle pin - solder the Unipulse D1 wire to the bottom pin of the switch for the clock connect...
by tubbutec
Tue Mar 17, 2020 5:35 am
Forum: Tubbutec
Topic: uTune microtonal midi through
Replies: 3
Views: 96

Re: uTune microtonal midi through

If you use CV/Gate to midi conversion, you can set the midi channel for each gv/gate input separately and thus define your voice allocation freely. When using Midi2µMidi conversion with sysec tuning, all is happening on one midi channel so no issue here. Currently when using midi2µMidi in pitch bend...
by tubbutec
Tue Mar 17, 2020 5:32 am
Forum: Tubbutec
Topic: Jupiter 6 Europa mod alternative
Replies: 2
Views: 87

Re: Jupiter 6 Europa mod alternative

We are currently still working on the 2oh2 mod. If that is finished a Jupiter 6 mod might be the next project, provided that synthcom will not re-release Europa in the meantime.
by tubbutec
Fri Mar 13, 2020 9:17 am
Forum: Tubbutec
Topic: uTune doesn't output Pitch.
Replies: 3
Views: 175

Re: uTune doesn't output Pitch.

Hi, If you see the input changing, you probably do not need to re-calibrate it. The reason why it gives you that error message is clearly because the outputs are not working. I suspect there is some problem with HW17 and the new firmware. Please do the following: - Reset the settings to default. If ...
by tubbutec
Thu Mar 12, 2020 8:30 am
Forum: Tubbutec
Topic: Unipulse can't respond to fast triggering with active sensing.
Replies: 2
Views: 248

Re: Unipulse can't respond to fast triggering with active sensing.

Hi Synthbuilder thank you very much for this. Helps a lot and we will look into it right away. Indeed this could be the reason uniPulse does not work properly with an MPC.
by tubbutec
Thu Mar 12, 2020 8:28 am
Forum: Tubbutec
Topic: Noise/hum when plugging into MIDI IN on SH1oh1
Replies: 10
Views: 498

Re: Noise/hum when plugging into MIDI IN on SH1oh1

This might be a power supply issue. You might want to check your electrolytic caps.
by tubbutec
Thu Mar 12, 2020 8:26 am
Forum: Tubbutec
Topic: The uTune Dual Expanders are here!
Replies: 9
Views: 679

Re: Are the uTune Dual Expanders dead?

It's true. We are currently in production. If you are on our notification list, you should have gotten an email with early access. If you did not get an email, please contact us. thanks
by tubbutec
Thu Mar 12, 2020 8:09 am
Forum: Eurorack Modules
Topic: µTune - Micro Tonal midi cv converter, quantizer, editor
Replies: 442
Views: 32203

Re: µTune - Micro Tonal midi cv converter, quantizer, editor

Please let me know if for some reason you did not get an email with access code to our shop. Thank you :)
by tubbutec
Mon Mar 09, 2020 11:08 am
Forum: Eurorack Modules
Topic: µTune - Micro Tonal midi cv converter, quantizer, editor
Replies: 442
Views: 32203

Re: µTune - Micro Tonal midi cv converter, quantizer, editor

Hi, I have not followed this thread for a long time, sorry if I missed some posts. Very happy to announce the µTune expanders are finally ready. If you are on our notification list you got mail today (if not please get in touch). We will officially announce the expander and send it to shops in the c...
by tubbutec
Thu Jan 30, 2020 2:22 am
Forum: Tubbutec
Topic: uTune video
Replies: 2
Views: 297

Re: uTune video

A series of videos is planned. Now I only need to find the time to make them ..
by tubbutec
Thu Jan 30, 2020 2:19 am
Forum: Tubbutec
Topic: Noise/hum when plugging into MIDI IN on SH1oh1
Replies: 10
Views: 498

Re: Noise/hum when plugging into MIDI IN on SH1oh1

This is off for the simple reason that midi is not ground coupled. So there should be no additional noise via a ground loop.
Is the noise just there if you plug it in, or only if you also send midi? Does it go a away if you stop sending midi clock and notes?
by tubbutec
Thu Jan 30, 2020 2:18 am
Forum: Tubbutec
Topic: everything works except portamento
Replies: 2
Views: 308

Re: everything works except portamento

I am very puzzled it is not working. Normally it works out of the box, without you having to adjust any settings. Normally you just use the RANGE switch of the ARP to select between the portamento speeds. I of course assume you did try that switch. I wonder if the RANGE switch is working at all in y...
by tubbutec
Thu Dec 19, 2019 12:18 pm
Forum: Tubbutec
Topic: Elektron machinedrum controlling Unipulse probs
Replies: 2
Views: 156

There was/is a similar problem with MPCs as reported elsewhere in the forum. So far we don't know what causes this, but this helps tracking down the problem. Thanks
by tubbutec
Wed Dec 18, 2019 9:27 am
Forum: Tubbutec
Topic: uTune microtonal midi through
Replies: 3
Views: 171

'corrupted data' display is normal after an update to 1.12, nothing to worry about. I tried this again and it works flawlessly. What are your settings in CONF->Midi->Output Config -> CH1, Mode? You need to choose Sysex or Bend here What files have to be in the root folder besides the firmware (and S...
by tubbutec
Tue Dec 17, 2019 6:19 am
Forum: Tubbutec
Topic: uTune microtonal midi through
Replies: 3
Views: 171

The following steps need to be taken to allow midi to microtonal midi conversion. This is how to do it with firmware 1.12 and might differ in later versions. 1) In the midi router you can select normal midi routing (an 90° arrow) and microtonal routing (an arrow + µ). If you want to translate midi...
by tubbutec
Tue Dec 17, 2019 6:14 am
Forum: Tubbutec
Topic: Occasional glitches in CV output
Replies: 4
Views: 300

thanks for reporting, if you find bugs in 1.12 please let us know. We are working towards a release version and every report is welcome.
by tubbutec
Mon Dec 09, 2019 4:58 pm
Forum: Tubbutec
Topic: Occasional glitches in CV output
Replies: 4
Views: 300

Hi, thanks for reporting.
this might be an issue with the beta firmware 1.11
1.12 is out know, maybe yu give it a try (still beta with bugs)
Or of course you go back to a stable version like 1.05

Go to advanced search