Jep the cgs instructions do have a little more Information.

Good evening everyone I have a question Regarding the envelopes. I did as one can read everywhere and setted pin 10from the lm3900 to +4v but during start in end is patched. The envelope cycles all seems good. But I do not really get a proper envelope when I plug in a gate in start, only small trigg...

Also think the Blackseq. Is the most intuitive sequencer in eurorack it has all what one could wish. Only the copiing steps to the next bar is a little weird I think it would be super handy if the first 16steps would copy automatically to the next bar. @girts Also brobability options for ratchets wo...

:cloud: received mine yesterday,i am so happy with it. it pairs super nicely with the ER301 from orthogonal devices for breakbeat mangling :yay: :yay: Firmware dream request : I would love to see probability on more than only gates, ratchets, glide, all the mod functions this would be super sick if ...

hi lytrix, glad i could help. my biggest mistakes all came from placing smd resis the wrong way arround, caused by the super chaotic pcb design. so thats really something to look at always in this project.! i have to check what i exactly did, with the constant pitch drop. but i remember jumper to gr...

anyone has experimented with longer Decay reverb tanks ?
thx
s

Two fold post here. 1. Does anyone have panel artwork to do serge paper face modules, To Print out and use for a face plate to drill, then laminate? DUSG SSG Wavemultiplier, etc. etc I have re-made many of the paperface graphics. Like real Serge, these are not always of the same era - for instance,...

My FHX-8GT also doesnt work. I first connected wrongly the 10pin cable to the to esx out on the fh-2. hope that didnt fry my fhx-8gate. it now blinks after a few seconds red on all outs of the module. the fh-2 seems to be fine. eieieieieieiei no connection possible to the fhx-8gate. i still have pro...

i am wrapping my head around this thing right now. the glide circuit currently pulls down all my there oscillators in pitch. I narrowed it down to ic 21 ( in the schematics the pinout is switched as on the board) on leg 3 (schem.5)I do have without anything plugged into the jack cv in, 0 voltage but...

Done it was a wrong resi. juhuuu.now i can tune that little fella.

I am almost done everything works now. except I can't tune oscillator 1 as the scale trimpot doesn't do anything, ( on osc2 and 3 it works) and my oscillator 2 is quite far down in pitch what doesn't seem right even without calibration. have to check now R17 and r21 I guess for the scale on osc1. an...

For the 2N3392 the schematics says 'Selected' does that mean the Hfe?
also Is it necessary to Match the T23 and T24 ?

Hi, I wanted to try to use the FH-2 as a midi host today. So I connected my OP-1 via a USBmini to USBC cable on the USB-C port of the FH-2. Pyramid was connected via USB A port and USBmini. I setted everything and enabled midi forward from usb a to c and vice versa, but I wasn't able to get any conn...

i just found out all the legs of lm348 are differntly pinned out in the euro version than in the schematics. eieiei :woah: :woah: :woah: . this doesnt make it easier to debugg. @oldcrow it would be so helpful to have dedicated eurorack schematics or at leaste eagle images of the boards. Such i tight...

so two of the there are running now somehow but very quirky, the octave switch won't let me go higher than 250hz at 8'. I did use 1k tempcos with the right resi values, as those are suggested in the euro build. Osc 2 still is so low frequent that I can see the frequency on my scope only if I turn up...

I hope anyone reads this: I figured out that I have a very low oscillation on all three oscillators. the highest frequency I am able to generate is 8 hz. I guess I have a wrong resistor value somewhere in there or a wrong cap. anyone has a hint.? all the waves are there if I switch between all of th...

IMG_9540.JPG Hi everyone, I am currently building the euro version of the Crowminius. as the euro build seems to be quite similar to the normal one I will write here in the hope anyone answers. ( dedicated euro schematics and any kind of silkscreen documentation would be very helpful at this point!...

i was wondering if I can manage to somehow get an clock from the trigger out mode of the op-1 into th FH-2 via one of the cv inputs.(it is a trigger signal)
is it possible to "clock" the FH-2 externaly this way ?
cheer
s

Model D, K2, Neutron and Pro One EXPANSION -------powered 20HP Case ------- . Hi everyone, we are wrapping our heads around a new idea at the moment and we are wondering if there are any interests in this: Almost one year ago we started a little 20hp expansion DIY case for the Moog Mother and DFAM ...

i cant find the way: move to other topic.+
arrrrgh

Model D, K2, Neutron and Pro One EXPANSION -------powered 20HP Case ------- Hi everyone, we are wrapping our heads around a new idea at the moment and we are wondering if there are any interests in this: Almost one year ago we started a little 20hp expansion DIY case for the Moog Mother and DFAM fo...

thanks @agawell.

thonk only has the kit. i will write them and ask if they will sell me only the pcbs and the panel.

cheers.

hi there, anyone knows if its possible to buy a only Pcb panel kit somewhere?

hi @oldcrow,
im currently building the DIY version of the euro crowminius.
Does it make sense to glue TH tempcos to the LM3046 solder the legs to the SMD pads?
the panasonic smd tmepcos are dicontinued and I am not able to get them anywhere anymore.

cheers
s

here is may mouser basket: https://www.mouser.de/ProjectManager/ProjectDetail.aspx?AccessID=aa5801888c Edit: BE AWARE !!!! the toggles in my basket are wrong !!!!! the right ones are those: Mountain Switch 10TC410 15x Mountain Switch 10TC415 2x it contains everything except: LM1458D SMD PArts 9mm po...