Do you have pic of 84hp/6U with long wooden side panels?

OVERRIDE INDICATORS : A dot appears over any value that’s currently overwritten by a loaded preset. In this case, the value displayed on the screen reflects the loaded preset value, which might differ from the front panel controls (until the front panel controls are modified, in which case the indic...

Wow.....interesting..

All the presets I saved are erased after power cycle. While module is on, save and load are fine. Since it gets erased after power off, it won’t come back to preset 1 either I followed procedure according to manual..... well....saving procedure is not complicated though..... What am I doing working ...

Ooooops.... My bad.....analog out's numbering is from 9........

Main L,R and headphone outs are all working fine.
3.5mm inputs are working fine.

Just 3.5mm outs are not working.

What can I do to fix that?

I did reinstall firmware. Still not working

Miracle just happened.
Once I touched output filter, all distortion went away… this is also weird though…..

Hello. Can you see my videos if it's OK? Erica says this is normal behavior but I think this unit definitely something wrong. Sound distorts depending on the speed and direction of turning shape knob If you turn the shape knob down slowly, it’s ok If you turn the shape knob down fast, it distorts so...

Just ordered. Looks so well built

I hope I can get that mult too.

So is this normal behavior besides incredibly harsh sound?

If I bring down 8th slider or 1st slider when all the sliders up, it starts to sound less harsh.

It doesn’t look like normal HO behavior, also it doesn’t sound like an HO at all. That sound is incredibly harsh with none of the organ-like blend of harmonics. Quick question: which power supply are you using? I tried ADDAC 901, makenoise skiff powered, tiptop happy ending, Intellijel 7U. THey're ...

yellowecho wrote: ↑

Wed Aug 19, 2020 11:25 am

That definitely seems abnormal to me. I'll test mine tonight to confirm though.

Please. Thanks

Hello. I have an issue with VHO. If I have the width parameter set past 12 o'clock and sliders all the way up, no sound. If I bring the sliders down it's OK Or if I move spectral tilt knob with all the sliders up, it starts making sounds. Here is the link https://www.dropbox.com/s/o0ypq2gq1ys0vw6/Ha...

Yes.
But I want to control(or CVing(?)) the length dynamically

Can you make pattern length globally?
Let's say I want to repeat all 8 tracks from step 3 to step 14....

igorrr wrote: ↑

Thu Jul 23, 2020 9:19 am

"Radio" effect can be found in Shaper category.

Where can I find this, please?

Did you try different case?
I have same problem with Cwejman SM-1 but it turned out to be case's power problem

virtualpt wrote: ↑

Fri Jul 24, 2020 12:42 pm

Yes, there are multiple ways to achieve this. See Settings>General section in manual

Thanks!

Can you have last state(algorithm, settings, z knob...) after power off and on?

Variable length would be nice indeed, e.g. stop capture and that would define the length until erased. I often don't need 10 (or rather 12 seconds) of buffer and then have to manually control spray and the range of scan CV to not dig into the empty part of the buffer. But i guess it would be tricky...

Was not aware of this! What's the technicalities behind? I have the same case with lots of Cwejman filters installed. I don't typically place them in self-oscillation so never thoroughly tested in the ADDAC901M. I have an SM-1 in a TTA 252 case so I guess I can test this out between cases and/or a ...

Does latching mode for capture gate input work? Mine works only for momentary. Hold shift + capture and moving dub knob fully clockwise, correct? Each time capture input gets trig signal, it blinks white. That's it. Can you make layer's duration something other than 10 seconds? What would you do if ...

I am using Hel

Sound doesn't change and no volume changes when you change "VOICES" with "SPREAD" at zero.
I guess this is normal behavior, correct?

Sound starts changing and volume drops when I turn "SPREAD" knob.
Is this also normal behavior?

I think by now it is established that some Cwejman modules are picky when it comes to power, as well as that switching PSUs have some issues inherent in their design Did you experience any other noticeable differences besides self-oscillating between analog and digital psu with Cwejman modules? Mak...