What about the noise of the MSCL, i mean its a great compressor but i leave the make up gain under 9'a clock otherwise the noise is really annoying.

When i saw a few demo's from the perfourmer and the Drm I couldn't resist, they are built like tanks the sound is super, Cv,gates...... i think the best part are the inserts, possibilities are endless.

Klee sequencer

running firmware 3.0, but my beats get chopped up when i clock the bitbox, no matter in which quantize i'm in. using clip cells, the clocking is not stable, and makes the beats run odd.... Someone else with same issue?
Never had this when running 2.0.

I have a rack sitting next to my modular with a vermona Perfourmer with CV and gates + a Vermona DRM MKIII with triggers. Currently waiting for a cirklon.

Well you might as well build a clouds and a rings if DIY is the possibility, i built 3 ripples and still use em every patch. You can grow slowly and learn every module. Peaks can be deep, so enough playground for a wile.

I'm on the fence for this for months, but always bought other modules. Stupid i know, but now it is time for the last module of my case and this is the one. Out of stock everywhere indeed, there are a few on mod grid though but think i'll wait for a newbaked.

So finaly got some time and after resoldering pin 8 and R1 still no connection. So i hardwired those 2 points and the pitch on slider 1 changes. Did not check voltages yet but calibrated before the fix with slider 2. Must say that i find it strange, those 2 points are like 5mm next to each other but...

Is there a manual available for the latest firmware? Cant seem to find it...

Digital U6 pin 8 (about +11.5V) = 13,03v
Analog U1 pin 13 (about +11.5V) = 13,03v
Analog U1 pin 1 (+4V) = 4,02v
Analog U1 pin 2 (+4V)= 4,02 v
Analog J5 pin 8 (+4V) = 4,02v
Analog J7 pin 8 (+4V) = 4,02v
Analog U8 pin 2 (+4V) = 0v
Analog U8 pin 1 (+4V) = 0v

Silder 1 does not change in pitch or in voltage, slider 2 for example does this without a problem. I reflowed the solder joints but no luck. But this is the problem im facing. I tought i heard it earlier in the bring up, all sliders affected the pitch, except for slider 1.

It makes sense, but the measurement between ground and pin 1 of U8 is zero because i trimmed it to zero with R42, changing the rotary switch position does not change that, also the trimpots for the positions of the rotary switch dont affect this. it wil remain zero, only R42 can raise the voltage.

Last question hopefully, Set pattern switch 1 to “ON” or “1”. • Set pattern switches 2 through 16 to “OFF” or “0”. • Press the Manual Load Switch so that only the Stage 1 LED is illuminated. • Rotate the Stage 1 Programming Pot to full CW. • Ensure Programming Pots 2 through 16 are all set full anti...

Ok.... i thought so. So anti clockwise meaning slider down i presume?

Hello, me again. So i wanted to continue with the bring up but somehow i dont get trough the next step. I simply dont understand the " programming" pots. Testing the Voltage Outputs A+B Output, Glide A+B Control Though the Klee is not calibrated yet, it should still provide a high enough voltage in ...

A7 turn out to work fine now, dont know why, Top lug switch A7 and pin 2 of P104 (pin 1 is the square pad).-> OK P104 pin 2 and Digital J4 pin 2 (spanning from daughterboard to A/D board).->OK Digital J4 pin 2 and right side of Digital R7.->OK Digital J4 pin 2 and Digital U6 pin 22.->OK Intermitten...

Ok thanks for the help, i did all the tests. A7 turn out to work fine now, dont know why, Top lug switch A7 and pin 2 of P104 (pin 1 is the square pad).-> OK P104 pin 2 and Digital J4 pin 2 (spanning from daughterboard to A/D board).->OK Digital J4 pin 2 and right side of Digital R7.->OK Digital J4 ...

So a few questions, i build the kit recently but did not get far trough the bring up. Question about the copied text from the manual. Now, check to see that +V and ground will make it to the Digital Board. Connect the positive lead of the ohmmeter to pin 1 of J10 and connect the negative lead to pi...

Ok, with negative, i meant that both points measure 0 Ohms between analog and digital board, i did the measurement with no power connected...

I will check the switches, but i never had a faulty one in my life so probably solder joint problems.... will check everything first.

So a few questions, i build the kit recently but did not get far trough the bring up. Question about the copied text from the manual. Now, check to see that +V and ground will make it to the Digital Board. Connect the positive lead of the ohmmeter to pin 1 of J10 and connect the negative lead to pin...

First thing i did when i bought a DRM and a perfourmer was buying a dozen insert cables to apply effects on the sounds.

Already put the shakmat stuff on my list

I have no experience with bloom, i wanted it a few weeks back but i see a that some people suffer with unwanted things so i did not buy it yet. I have eloquencer as my main sequencer and for patterns programmed by yourself it works very well, when i jam and have 8 patterns which are pre programmed, ...

I also own one of these, bang for the buck Vca/mixer in my opinion.

Mutable instruments frames with parasites does this.