Those carry some current so you want the parts in the BOM or equally power rated 0805s which i guarantee you dont have on hand since they are exotic and expensivePolysilicon wrote: ↑Wed Jan 27, 2021 12:23 amQuestion for assembly: do I need to use 1206 resistors for R1 and R3 or can I use 0805?
Search found 3514 matches
- Wed Jan 27, 2021 6:57 am
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
Re: Neutron sound Dust of Time.
- Sun Jan 24, 2021 11:54 am
- Forum: Music Tech DIY
- Topic: EURO x0x-heart - Complete "Kit"
- Replies: 353
- Views: 17330
Re: EURO x0x-heart - Complete "Kit"
I am building this and have a problem. the ERA-V33J561V 560 ohm temp co 3300ppm resistor is now obsolete with nothing even close to it as an alternative. Could someone explain what it does and what should I do as an alternative. tia use 2 1k in parallel and change a resistor value (I forget which o...
- Sat Jan 23, 2021 6:55 am
- Forum: Music Tech DIY
- Topic: uO_c 8hp ornament and crime.
- Replies: 362
- Views: 49273
Re: uO_c 8hp ornament and crime.
Yeah, I don't have a spacer between screen and panel. Looked at my local electronics store and ace hardware, no luck on 3mm spacer. But I just measured it and I think 3mm might actually stretch the panel. I probably should have used a socket for the screens pins instead of soldering directly. The c...
- Wed Jan 20, 2021 11:08 am
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
- Tue Jan 19, 2021 7:17 am
- Forum: General Gear
- Topic: Behringer: practices, ethics, morals and legitimacy.
- Replies: 2396
- Views: 114689
- Mon Jan 18, 2021 6:58 am
- Forum: Music Tech DIY
- Topic: Polyphonic MIDI to CV Conversion
- Replies: 18
- Views: 494
Re: Polyphonic MIDI to CV Conversion
Might want to look through the yarns code how and see how she implemented it.
https://mutable-instruments.net/modules/yarns/
https://mutable-instruments.net/modules/yarns/
- Sun Jan 17, 2021 11:24 am
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
Re: Neutron sound Dust of Time.
Thats the official one. I havent recently looked at whats in and what isnt in stock but there really isnt anything specific needed, any equivalent spec parts will be fine
- Sun Jan 17, 2021 5:57 am
- Forum: Music Tech DIY
- Topic: uO_c 8hp ornament and crime.
- Replies: 362
- Views: 49273
Re: uO_c 8hp ornament and crime.
it looks like your missing the 3mm spacer at the top between the screen and panel so the buttons are catching on the flexed panel. The height of the panel at the top should be 10mm off the PCB. Its PCB-6mm spacer-screen-3mm spacer-panel
- Fri Jan 15, 2021 8:04 am
- Forum: Music Tech DIY
- Topic: Two Thousand Six Hundred (TTSH) Ver.2 General build thread
- Replies: 1499
- Views: 97928
Re: Two Thousand Six Hundred (TTSH) Ver.2 General build thread
hi, after ..5y ? i'm finally about to power on my rev1.7 speakers and phone wired (no reverb tank for now).. but i'm a bit worried cause really i'm not an electrician at all. i did mesure the +15-15 years ago.. and went on with th vcos. hope nothing smokes i have security glasses on. question : i r...
- Fri Jan 15, 2021 8:00 am
- Forum: Music Tech DIY
- Topic: uT_u 8HP micro Temps Utile build
- Replies: 47
- Views: 4162
Re: uT_u 8HP micro Temps Utile build
when you have a way off ADC input like that, that usually means an open connection between the input and the teensy. Its 4 resistors and half an opamp per channel, check those again. Using 0.1 parts is really not needed, youre trimming the ADC anyway so it literally makes no difference if you use 5%...
- Thu Jan 14, 2021 6:01 pm
- Forum: Music Tech DIY
- Topic: uT_u 8HP micro Temps Utile build
- Replies: 47
- Views: 4162
Re: uT_u 8HP micro Temps Utile build
look again. its a soldering issue on the input or a wrong value. check the opamp legs
- Tue Jan 12, 2021 9:44 am
- Forum: Music Tech DIY
- Topic: DIY Mutable Unsuccessful Builds
- Replies: 3660
- Views: 237294
Re: DIY Mutable Unsuccessful Builds
The dot on the switch should be on the same side as the dot on the PCB, it looks like it is
- Sun Jan 10, 2021 7:08 pm
- Forum: Eurorack Modules
- Topic: Hackme Vectr - 3D Sensing Controller and Sequencer
- Replies: 387
- Views: 33605
Re: Hackme Vectr - 3D Sensing Controller and Sequencer
The files in the github repo are no good.
- Sat Jan 09, 2021 7:55 am
- Forum: Music Tech DIY
- Topic: 2021 : which soldering station, desoldering gun, etc,?
- Replies: 35
- Views: 750
- Fri Jan 08, 2021 8:38 pm
- Forum: Music Tech DIY
- Topic: 2021 : which soldering station, desoldering gun, etc,?
- Replies: 35
- Views: 750
Re: 2021 : which soldering station, desoldering gun, etc,?
I'd skip the FX-888 and go straight to the FX-951. Yes its more than twice as expensive but its also about half as much as similar higher end irons that use heater tips (the single heater/temp sensor/tip things) and if you're planning on soldering anything other than occasionally, its well worth it...
- Thu Jan 07, 2021 8:01 am
- Forum: Music Tech DIY
- Topic: 2021 : which soldering station, desoldering gun, etc,?
- Replies: 35
- Views: 750
Re: 2021 : which soldering station, desoldering gun, etc,?
I'd skip the FX-888 and go straight to the FX-951. Yes its more than twice as expensive but its also about half as much as similar higher end irons that use heater tips (the single heater/temp sensor/tip things) and if you're planning on soldering anything other than occasionally, its well worth it:...
- Sat Jan 02, 2021 7:29 am
- Forum: Music Tech DIY
- Topic: TB303 powered by a One Spot, weird thing & sanity check
- Replies: 2
- Views: 118
Re: TB303 powered by a One Spot, weird thing & sanity check
You have to hold pitch mode then press the key or transpose buttons in play mode. If there are no batteries in the 303, it wont hold the programs so it will give you grabbled patterns
- Thu Dec 31, 2020 6:59 am
- Forum: Music Tech DIY
- Topic: PCBs as Front Panels ?
- Replies: 233
- Views: 23183
Re: PCBs as Front Panels ?
Ordered several Erica synth panels from JLCPCB. Quite amazed by the quality. Looks like proper aluminium panels I only know now that the next time, I have to remove number order from the front :doh: Such a waste... There are specific instructions about that in the order instructions. You just put J...
- Sat Dec 26, 2020 3:48 pm
- Forum: Eurorack Modules
- Topic: Available Now: Neutron Sound Utility Modules
- Replies: 4
- Views: 712
- Tue Dec 22, 2020 6:38 am
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
Re: Neutron sound Dust of Time.
.. . Thanks for the Panel/PCBs btw. I saw that you did a Miasma build before, can you recommend a place to get PCBs done in low quantity? What about panels? I haven't done that part of DIY stuff yet. JLC for both the panel and PCB. Get a 2mm panel, not the stock 1.6mm thick. I had a lot of problems...
- Mon Dec 21, 2020 6:42 pm
- Forum: Music Tech DIY
- Topic: Software for viewing code
- Replies: 15
- Views: 462
Re: Software for viewing code
notepad++
- Mon Dec 21, 2020 7:25 am
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
Re: Neutron sound Dust of Time.
You can get the jacks from synthcube or modular addict
- Sat Dec 19, 2020 7:56 pm
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
- Sat Dec 19, 2020 6:46 am
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
Re: Neutron sound Dust of Time.
They are all current. The DIY version is available with the tact switches or the click pots and each of those have their own panel. The circuit board for the electronics is the same thing for both versions (you simply dont populate some parts). The click pot version is NOT currently in stock since t...
- Thu Dec 17, 2020 5:52 pm
- Forum: Music Tech DIY
- Topic: Neutron sound Dust of Time.
- Replies: 316
- Views: 21342
Re: Neutron sound Dust of Time.
under most circumstances, it will be fine if you dont cut the trace and accidentally power it up with the USB plugged in, the regulator is behind that trace so you will just be adding 5V to it but in the DOT, what will happen is that you will murder the SD card. You can solder blob it even after its...