Behringer Go eurorack case

Cwejman, Livewire, TipTop Audio, Doepfer etc... Get your euro on!

Moderators: Kent, luketeaford, lisa, Joe.

Post Reply
Don Cajon
Learning to Wiggle
Posts: 5
Joined: Sat May 23, 2020 6:07 am

Re: Behringer Go eurorack case

Post by Don Cajon » Mon May 25, 2020 4:14 pm

Great to hear that your PSU seems ok. I'll try to get a replacement then.

Dennis
Common Wiggler
Posts: 127
Joined: Sun Jan 07, 2018 3:25 am

Re: Behringer Go eurorack case

Post by Dennis » Tue May 26, 2020 12:16 am

maybe its a module tho? i had noticed as i racked more and more distortion modules, sadly they bring ALOT of noise into any system / case / psu (just like guitar pedals i should have known better :-D )

User avatar
scutch
Common Wiggler
Posts: 136
Joined: Fri Jun 15, 2012 10:41 am
Location: Dublin

Re: Behringer Go eurorack case

Post by scutch » Tue May 26, 2020 4:27 pm

Got mine today. Really like it. Build quality is good, no loose connections, nothing feels flimsy and the stand provides a nice playing position. Would have liked a bit more of a lip on the built in handle at the back but I don't think I'd be carrying it more than moving around my house.

I don't have the issue with the PSU mentioned earlier in the thread. Forgot how much I hated sliding nuts but for the extra hp and cost vs other cases it's a trade off I'm ok with. With that said I was a bit nervous about plugging a module in that cost 2x what the case does but so far so good.

OldManZero
Learning to Wiggle
Posts: 10
Joined: Sat Jun 29, 2019 11:13 pm
Location: Orange County, California

Re: Behringer Go eurorack case

Post by OldManZero » Wed May 27, 2020 5:46 pm

I received mine last week and did an unboxing and general overview of how it feels when I switched over my modules from a Mantis in case anyone wants to see a hands-on.

Part 1: Unboxing and First Thoughts


Part 2: Manual Read, Module Loading, and Final Impressions

User avatar
h4ndcrafted
Super Deluxe Wiggler
Posts: 3994
Joined: Wed Jan 18, 2012 2:27 pm

Re: Behringer Go eurorack case

Post by h4ndcrafted » Wed Jun 10, 2020 1:55 pm

Got mine today, holy plastic ! At least the runners are metal!

You get what you pay for. I’m way more excited about the filter bank, it’s a lot of fun, no CV control though.

It has nice chunky feet on the front and the stand is good. If you were to drop it , it feels like it would splinter into a thousand pieces of plastic lol

More like Behringer stay than go, which is fine because it’s staying put!

Oh I forget , the case does whine a bit if you get up close, high pitched, but not too bothersome at the moment. If it gets annoying it’s going back to Germany.
Attachments
79C056CB-7CFD-453A-8554-ADDBC975413D.jpeg
Last edited by h4ndcrafted on Wed Jun 10, 2020 2:13 pm, edited 1 time in total.
We don't want to conquer space at all. We want to expand Earth endlessly. We don't want other worlds; we want a mirror.

User avatar
deke
Wiggling with Experience
Posts: 370
Joined: Tue Sep 23, 2014 6:48 am

Re: Behringer Go eurorack case

Post by deke » Wed Jun 10, 2020 2:11 pm

My sanctimonious sense of unique artistry and ultra hip non conformity prevent me from considering the purchase of this case, though I am now troubled as perhaps buying this case could be a powerful demonstration of how unique and non conforming my artistry and hipness actually are! It is so hard being a free thinking individual.

User avatar
deke
Wiggling with Experience
Posts: 370
Joined: Tue Sep 23, 2014 6:48 am

Re: Behringer Go eurorack case

Post by deke » Sun Jun 14, 2020 9:12 pm

I’m trying not to take this personally, but I seem to have a gift for killing threads. This has to be at least number six. There must be a way to find out.

User avatar
pieter
Super Deluxe Wiggler
Posts: 1683
Joined: Tue Dec 01, 2015 2:59 pm
Location: UK

Re: Behringer Go eurorack case

Post by pieter » Mon Jun 15, 2020 2:54 am

Well, it's very difficult to respond to your previous message. Was it sarcasm? Was it self-deprecating humor? Remember Poe's law on the internet: we can't hear your intonation.

To keep a thread going you want to phrase your point constructively, and in such a way that it invites response.

User avatar
Paranormal Patroler
Super Deluxe Wiggler
Posts: 11016
Joined: Tue Aug 30, 2011 3:40 pm
Location: the Terminal beach

Re: Behringer Go eurorack case

Post by Paranormal Patroler » Mon Jun 15, 2020 4:48 am

OldManZero wrote:
Wed May 27, 2020 5:46 pm
I received mine last week and did an unboxing and general overview of how it feels when I switched over my modules from a Mantis in case anyone wants to see a hands-on.
Thank you for the videos. Quite informative.
I'm curious if B will actually decide to make stands for this, or if the Mantis ones can be repurposed to that end
All rights reserved; all wrongs reversed.

User avatar
deke
Wiggling with Experience
Posts: 370
Joined: Tue Sep 23, 2014 6:48 am

Re: Behringer Go eurorack case

Post by deke » Mon Jun 15, 2020 11:53 am

pieter wrote:
Mon Jun 15, 2020 2:54 am
Well, it's very difficult to respond to your previous message. Was it sarcasm? Was it self-deprecating humor? Remember Poe's law on the internet: we can't hear your intonation.

To keep a thread going you want to phrase your point constructively, and in such a way that it invites response.
Alas my sarcastic approach to humor truly has to be experienced in person! In both posts!

User avatar
dooj88
Super Deluxe Wiggler
Posts: 1691
Joined: Sun Jan 29, 2017 7:31 pm
Location: lovettsville, va
Contact:

Re: Behringer Go eurorack case

Post by dooj88 » Mon Jun 15, 2020 3:17 pm

muffs moves pretty slow. i wouldnt take anything personally.

Efudd
Common Wiggler
Posts: 69
Joined: Sat Apr 11, 2020 1:06 pm

Re: Behringer Go eurorack case

Post by Efudd » Mon Jun 15, 2020 10:47 pm

Liking the Go case for HP/$. Replaced the nuts with threaded strips to make them tolerable. Some modules may have clearance issues around the handle inset (center top row).

Two cases and a quick 3d print I modeled up (two, one on each side); It needs to be reprinted a little taller. In an ideal world the angle would be steeper but I wanted to not have to mess with a riser for the kickstand yet.

I could see spending more time on combining these cases into a more permanent installation, potentially three high.
2CC19587-BC66-4B42-8717-C1E8E8E3901A.jpeg
8D9407D2-F627-41B8-851D-CC29D1B282EA.jpeg

Dennis
Common Wiggler
Posts: 127
Joined: Sun Jan 07, 2018 3:25 am

Re: Behringer Go eurorack case

Post by Dennis » Tue Jun 16, 2020 12:22 am

wow looks awesome!

i don't know if i already mentioned, but i inserted threaded strips wich i bought for cheap on eBay and that helped a lot :-D
overall still very satisfied. actually played in a live jam with it and it was smaller than a keyboard synth but bigger than a elektron octatrack. so in that concern it doesn't take away too much space in small locations.

Don Cajon
Learning to Wiggle
Posts: 5
Joined: Sat May 23, 2020 6:07 am

Re: Behringer Go eurorack case

Post by Don Cajon » Fri Jun 19, 2020 7:55 am

So I got my replacement PSU today. Actually I got the entire case replaced, which I tried to avoid but well... logistics! :goo:
The PSU noise is a bit softer than the previous one but it still creates a high-pitched noise while the case is on, which you can hear when being in play-range of the synth.

Mabye somebody here has an idea where I could find a better quality PSU with 13V/5A?
Dennis wrote:
Tue May 26, 2020 12:16 am
maybe its a module tho? i had noticed as i racked more and more distortion modules, sadly they bring ALOT of noise into any system / case / psu (just like guitar pedals i should have known better :-D )
Yeah that's true, but in my "case" ( :mrgreen: ) also happens when I have no modules connected.
Efudd wrote:
Mon Jun 15, 2020 10:47 pm
I could see spending more time on combining these cases into a more permanent installation, potentially three high.

2CC19587-BC66-4B42-8717-C1E8E8E3901A.jpeg

8D9407D2-F627-41B8-851D-CC29D1B282EA.jpeg
I love it. Can't wait to see more of this :)

User avatar
h4ndcrafted
Super Deluxe Wiggler
Posts: 3994
Joined: Wed Jan 18, 2012 2:27 pm

Re: Behringer Go eurorack case

Post by h4ndcrafted » Mon Jun 22, 2020 7:06 pm

Mine does it too , but you have to be in the right place. With more modules in I rarely notice it. I suspect they all do it , but depending on placement , you either notice it or don’t.
We don't want to conquer space at all. We want to expand Earth endlessly. We don't want other worlds; we want a mirror.

Efudd
Common Wiggler
Posts: 69
Joined: Sat Apr 11, 2020 1:06 pm

Re: Behringer Go eurorack case

Post by Efudd » Mon Jun 22, 2020 9:49 pm

I normally identify aberrant sound quickly... so far I've not noticed any noise from the PSUs across three cases. My cases aren't in the quietest of areas at the moment though.

*EDIT*: Yeah, definitely humming from those... now I can’t unhear it. :)
Last edited by Efudd on Tue Jun 23, 2020 12:53 am, edited 1 time in total.

blakeq
Common Wiggler
Posts: 166
Joined: Tue Oct 20, 2015 8:38 am

Re: Behringer Go eurorack case

Post by blakeq » Mon Jun 22, 2020 10:22 pm

Which ones did you end up purchasing?
Dennis wrote:
Tue Jun 16, 2020 12:22 am
wow looks awesome!

i don't know if i already mentioned, but i inserted threaded strips wich i bought for cheap on eBay and that helped a lot :-D
overall still very satisfied. actually played in a live jam with it and it was smaller than a keyboard synth but bigger than a elektron octatrack. so in that concern it doesn't take away too much space in small locations.

User avatar
Notron fn
Wiggling with Experience
Posts: 261
Joined: Sat Feb 23, 2013 1:25 pm
Location: Olympia

Re: Behringer Go eurorack case

Post by Notron fn » Tue Jun 23, 2020 12:37 am

Has anybody measured their nuts? As in what kind of extra slider nuts would work with this case? (Frap tools m3 square nuts perhaps?)
Insert pithy statement here

Don Cajon
Learning to Wiggle
Posts: 5
Joined: Sat May 23, 2020 6:07 am

Re: Behringer Go eurorack case

Post by Don Cajon » Tue Jun 23, 2020 9:24 am

h4ndcrafted wrote:
Mon Jun 22, 2020 7:06 pm
Mine does it too , but you have to be in the right place. With more modules in I rarely notice it. I suspect they all do it , but depending on placement , you either notice it or don’t.
Mine is round about half full. I guess, with more modules in, the pitch will rise until its out of the hearing range.
Not sure what placement could have to do with this?
Efudd wrote:
Mon Jun 22, 2020 9:49 pm
I normally identify aberrant sound quickly... so far I've not noticed any noise from the PSUs across three cases. My cases aren't in the quietest of areas at the moment though.

*EDIT*: Yeah, definitely humming from those... now I can’t unhear it. :)
All of your three cases make the coil whine?

User avatar
s0lo
Wiggling with Experience
Posts: 410
Joined: Thu Feb 21, 2013 5:46 pm
Contact:

Re: Behringer Go eurorack case

Post by s0lo » Fri Aug 21, 2020 12:04 pm

I hate sliding nuts with a passion. Other than that, looks good to me. Thinking of trying it

Does any one know of a proper gig bag for this?

Don Cajon
Learning to Wiggle
Posts: 5
Joined: Sat May 23, 2020 6:07 am

Re: Behringer Go eurorack case

Post by Don Cajon » Sat Aug 22, 2020 1:25 am

s0lo wrote:
Fri Aug 21, 2020 12:04 pm
Does any one know of a proper gig bag for this?
Interested in a solution as well. I wouldn't put it in a bag without a cover, though.

User avatar
acinonyx
Common Wiggler
Posts: 63
Joined: Fri Sep 14, 2018 4:34 pm
Location: ギリシャ, Underground

Re: Behringer Go eurorack case

Post by acinonyx » Sat Aug 22, 2020 4:18 am

Don Cajon wrote:
Sat Aug 22, 2020 1:25 am
s0lo wrote:
Fri Aug 21, 2020 12:04 pm
Does any one know of a proper gig bag for this?
Interested in a solution as well. I wouldn't put it in a bag without a cover, though.
Gator GKB 49 or enything similar up to 49 keys I suppose.

Some reviews can be found here:

Behringer Eurorack Go:

https://www.thomann.de/gb/behringer_eur ... %5B%5D=all

Gator GKB 49:

https://www.thomann.de/gb/gator_gkb_49_ ... %5B%5D=all
"Eureka, Archimedes of Syracuse"

User avatar
Kattefjaes
Veteran Wiggler
Posts: 708
Joined: Thu Dec 12, 2019 9:47 am
Location: UK

Re: Behringer Go eurorack case

Post by Kattefjaes » Sat Aug 22, 2020 4:34 am

Notron fn wrote:
Tue Jun 23, 2020 12:37 am
Has anybody measured their nuts? As in what kind of extra slider nuts would work with this case? (Frap tools m3 square nuts perhaps?)
Try getting a cheap bag of m3 sliding nuts from Amazon first? Pop a couple out to check the profile if necessary first. Should be a really inexpensive buy.

User avatar
Tom_1970
Common Wiggler
Posts: 78
Joined: Thu Jan 14, 2016 3:39 pm
Location: The Netherlands

Re: Behringer Go eurorack case

Post by Tom_1970 » Wed Sep 16, 2020 9:09 am

Made a cabinet for my 2 Eurorack Go cases.
Eurorack-cabinet-1.png

finnurbjarna
Common Wiggler
Posts: 96
Joined: Sun Jun 29, 2014 2:32 am
Location: Brighton, UK

Re: Behringer Go eurorack case

Post by finnurbjarna » Wed Sep 16, 2020 11:02 am

Tom_1970 wrote:
Wed Sep 16, 2020 9:09 am
Made a cabinet for my 2 Eurorack Go cases.

Eurorack-cabinet-1.png
Wow - nicely done! :tu:

Post Reply

Return to “Eurorack Modules”