[AVAILABLE] TTSH V4 Build Thread

From circuitbending to homebrew stompboxes & synths, keep the DIY spirit alive!

Moderators: Kent, luketeaford, Joe.

Post Reply
kristop
Common Wiggler
Posts: 66
Joined: Thu Mar 24, 2016 12:31 pm

Re: [AVAILABLE] TTSH V4 Build Thread

Post by kristop » Sat Feb 27, 2021 12:15 pm

PXL_20210225_065058932.jpg
I think everything works.... One of the only things that seemed off was my Lag processor output looks more like the wave on the panel than what the Service Manual suggests.

User avatar
fallout
Common Wiggler
Posts: 93
Joined: Fri Dec 18, 2020 2:45 pm

Re: [AVAILABLE] TTSH V4 Build Thread

Post by fallout » Sat Feb 27, 2021 12:50 pm

kristop wrote:
Sat Feb 27, 2021 12:14 pm
fallout wrote:
Wed Feb 24, 2021 7:16 pm
Well... The LM301 strikes again!
I had to replace both in my S&H as I believe you mentioned a few pages back to get my clock speed down past 5 seconds.

The Buchla 208 build had similar issues with certain ICs too you cod just swap them around to different sockets to get things working properly. Frustrating but easier than looking for other issues.
Yes, I completely forgot about trying swapping the LM301 in the 4012 filter since it was for the most part working. I've been having a blast with my TTSH for the past few days and getting familiar with it. Fun stuff
kristop wrote:
Sat Feb 27, 2021 12:15 pm
I think everything works.... One of the only things that seemed off was my Lag processor output looks more like the wave on the panel than what the Service Manual suggests.
Hmm.. Mine looked pretty much like what's in the service manual. Doesn't seem like there's much to go wrong in that circuit. Are you using a TL071 as suggested and not a LM301? Are all of the cap values correct?

User avatar
bemerritt
Veteran Wiggler
Posts: 689
Joined: Fri Oct 09, 2015 12:22 pm
Location: San Clemente, CA

Re: [AVAILABLE] TTSH V4 Build Thread

Post by bemerritt » Sat Feb 27, 2021 9:59 pm

So what’s the secret to getting the wires on the red connectors that come with the synthcube kit?

User avatar
fallout
Common Wiggler
Posts: 93
Joined: Fri Dec 18, 2020 2:45 pm

Re: [AVAILABLE] TTSH V4 Build Thread

Post by fallout » Sat Feb 27, 2021 10:03 pm

bemerritt wrote:
Sat Feb 27, 2021 9:59 pm
So what’s the secret to getting the wires on the red connectors that come with the synthcube kit?
..Use Molex! :razz:

I personally hate those MTA connectors.

User avatar
KSS
Super Deluxe Wiggler
Posts: 4907
Joined: Mon Jan 25, 2016 7:28 am

Re: [AVAILABLE] TTSH V4 Build Thread

Post by KSS » Sat Feb 27, 2021 11:17 pm

They're fantastic when you have the right tools and use the correct wire. Absent those, they can suck.

User avatar
bemerritt
Veteran Wiggler
Posts: 689
Joined: Fri Oct 09, 2015 12:22 pm
Location: San Clemente, CA

Re: [AVAILABLE] TTSH V4 Build Thread

Post by bemerritt » Sat Feb 27, 2021 11:29 pm

KSS wrote:
Sat Feb 27, 2021 11:17 pm
They're fantastic when you have the right tools and use the correct wire. Absent those, they can suck.
Man, I don’t know if I want to pony up the $50 for the tool. Is it really that worth it? I take it there is a different tool for each size?

User avatar
sduck
experimental use of gravity
Posts: 14169
Joined: Wed Feb 18, 2009 6:03 pm
Location: Vortepexaion, TN, USA

Re: [AVAILABLE] TTSH V4 Build Thread

Post by sduck » Sat Feb 27, 2021 11:31 pm

Is it 50$ now? It was 30$ (and well worth it) the last time i checked. But, inflation....
flickr cloud of sound touyube NOT A MODERATOR ANYMORE

kristop
Common Wiggler
Posts: 66
Joined: Thu Mar 24, 2016 12:31 pm

Re: [AVAILABLE] TTSH V4 Build Thread

Post by kristop » Sun Feb 28, 2021 1:47 pm

i managed with a small flat head screwdriver and gradually pushed them in in three different spots, either side of the actual connection and into the connection.

kristop
Common Wiggler
Posts: 66
Joined: Thu Mar 24, 2016 12:31 pm

Re: [AVAILABLE] TTSH V4 Build Thread

Post by kristop » Sun Feb 28, 2021 1:53 pm

fallout wrote:
Sat Feb 27, 2021 12:50 pm
Hmm.. Mine looked pretty much like what's in the service manual. Doesn't seem like there's much to go wrong in that circuit. Are you using a TL071 as suggested and not a LM301? Are all of the cap values correct?
just checked it again and it's as per the manual. I guess it is done. :bacon:

Post Reply

Return to “Music Tech DIY”