DIY Trade Thread [ Parts, PCBs, Panels ]

[jonnyjupiter]

Anyone have an Extra Life Super 16 board and panel or full kit that they kickstarted but haven't built?

[jonnyjupiter]

I'm on the mailing list, but it would make a lovely Christmas present (to me from me).

[synth.void]

I ordered some of these by mistake (wanted 1.3"):
128x64 OLED Module SPI 0.96"Graphic Displays,White on Black

Just realized I have a couple of them too. Any ideas where they could be used?

Pretty sure they work for the 1u versions of o&c and temps utile (will also be easy to use in your personal teensy adventure)

Great point, thanks. I've also realised I could make a rather simple scope with it.

[DEEMARKAY]

I ordered some of these by mistake (wanted 1.3"):
128x64 OLED Module SPI 0.96"Graphic Displays,White on Black

Just realized I have a couple of them too. Any ideas where they could be used?

Pretty sure they work for the 1u versions of o&c and temps utile (will also be easy to use in your personal teensy adventure)

Great point, thanks. I've also realised I could make a rather simple scope with it.

Yes, VPME Zeroscope also uses this part.
One needs to watch out though since there are versions with different numbers of pins and different pinouts.

[synth.void]

One needs to watch out though since there are versions with different numbers of pins and different pinouts.

Yea, I went through the hell of launching a hello world with an Arduino and one of the screens. Pretty much trying out everything on the wiki page of u8g2. But it works!

[kevin0]

I have these PCBs to trade:

CGS/Serge - DUSG
CGS/Serge - VCS x 2
Stroh - FadeX4u

Looking for:

CGS/Serge: 1973 VCO
CGS/Serge: 1973 Filter x2
CGS/Serge: Router
CGS/Serge: W.A.D.
CGS: Dual CV Processor

[Phetus]

looking for 4x 2180 B VCA chips incase anyone has any floating around...

[revtor]

looking for 4x 2180 B VCA chips incase anyone has any floating around...

Phetus, I have a ton of the 2150’s. I’ll send you 4 for shipping cost if you want! Got any vca pcbs?
Steve

[revtor]

PCB’s found

Looking for 4u..
CGS79 ring mod
CGS31 digital noise.

I’ve got a couple 4u (2”x6”) “blessed by Paul” MOTM 700 dual bidirectional switch pcbs for trade. Or cash.

Thanks
Steve

[Bamboombaps]

Some blanks I have posted here before and some new ones
Looking for PCB panel sets

IMG_20201208_134636.jpg

[synth.void]

Still looking for an o_C panel.

[pjbulls]

Regular or micro? I have a few spare micro panels:



They are blue & white though (as shown) so that may not be everyone's cup of tea

[synth.void]

They are blue & white though (as shown) so that may not be everyone's cup of tea

Sorry, regular ones! But this one would look so good next to IOInstruments modules

[revtor]

Ghielmetti 20x20 matrix gathering dust anyone? Looking. . .

[CliffordMilk]

Has anyone in the UK got a spare E-switch LP4OA1PBCTG ?

These are the illuminated switches used on Mutable Clouds. I ordered the wrong part from Mouser recently.

I ordered the wrong part from Mouser and have a whole load of parts and knobs I would happily trade - just tell me what you need.

[synthetek]

Ghielmetti 20x20 matrix gathering dust anyone? Looking. . .

Hi, I have a phutney clone pcb set so I think this matrix is what I need, what are you looking for?
Thanks

[revtor]

Ghielmetti 20x20 matrix gathering dust anyone? Looking. . .

Hi, I have a phutney clone pcb set so I think this matrix is what I need, what are you looking for?
Thanks

I am looking to buy a matrix.
Thanks
Steve

[The_Elmo]

Has anyone in the UK got a spare E-switch LP4OA1PBCTG ?

These are the illuminated switches used on Mutable Clouds. I ordered the wrong part from Mouser recently.

I ordered the wrong part from Mouser and have a whole load of parts and knobs I would happily trade - just tell me what you need.

I have one extra, but I'm in Finland

I would need a couple of (two to be exact) STM32F103CBT6. The world seems to be out of them. I'd need them for my braids build.

[oberkorn]

Looking for
Programmed FMogre dsp chip
Blue and White Rogan knobs for Maths MkI
Radio Music switches (any colour) "C&K D6R90"
35mm arcade knob(s), any colour
Chord Organ panel

Can trade with
Assembled Thomas Henry SN-Voice board (without ICs)
"Mutable" PCBs (1 Riddles, 1 Streams and 2 Slides, see pics further up in this thread
Black Mutable Plaits and Clouds panels
Music Thing Radio Music panel (Black)
VOID Modular 8hp blank panel
TiNRS Tuesday PCB/Panelset
ST Krach aus Strom PCB/Panel set
Music Thing Mikrophonie PCB
Clacktronics speaker PCB
Hepthaphasis LFO PCB
ST Eurokastle PCB
Pot chicklet PCBs
Fonik Attentuverter PCBs

[B0bcat]

Looking to buy the following (I'm in SoCal) -

2x Alpha potentiometer (Thonk style - other Alpha clones unfortunately do not fit the panel hole) B250K - Round shaft 6.35mm - Alpha Vertical 9mm Potentiometer - MPN: RD901F-40-15R1-B250K

2x THAT 2180 A

Hit me up!

[KittenVillage]

Looking to buy the following (I'm in SoCal) -

2x Alpha potentiometer (Thonk style - other Alpha clones unfortunately do not fit the panel hole)

Hey, not to be an ass at all, but are you talking about ones without a rotation tag? That tag is so very simple to snap off with needle nose pliers that it's trivial to do. AFAIK no one but Thonk has ones without the rotation tag. Since you are in S. Cal, you may find that https://www.tubesandmore.com/ would ship fastest and cheapest to you. I think they are in Tempe, AZ.

I think you can find the THAT 2180A at mouser, but it's pricey.

[B0bcat]

Looking to buy the following (I'm in SoCal) -

2x Alpha potentiometer (Thonk style - other Alpha clones unfortunately do not fit the panel hole)

Hey, not to be an ass at all, but are you talking about ones without a rotation tag? That tag is so very simple to snap off with needle nose pliers that it's trivial to do. AFAIK no one but Thonk has ones without the rotation tag. Since you are in S. Cal, you may find that https://www.tubesandmore.com/ would ship fastest and cheapest to you. I think they are in Tempe, AZ.

I think you can find the THAT 2180A at mouser, but it's pricey.

Thanks - rotation tag or not doesn't matter, but there are "fake" Alpha pots that look fairly similar to the Thonk ones but have a slightly larger shaft diameter. I've tried before, unsuccessully, to fit them through Random Source panels.

The ones on Tubesandmore, at least on the photos, look like the non-fitting ones.

Re: THAT chips, they're out of stock at Mouser, ETA March or May or 50 weeks.

[elmegil]

Thanks - rotation tag or not doesn't matter, but there are "fake" Alpha pots that look fairly similar to the Thonk ones but have a slightly larger shaft diameter. I've tried before, unsuccessully, to fit them through Random Source panels.

I would recommend getting one of these

https://www.harborfreight.com/t-handle- ... 5AQAvD_BwE

[B0bcat]

Thanks - rotation tag or not doesn't matter, but there are "fake" Alpha pots that look fairly similar to the Thonk ones but have a slightly larger shaft diameter. I've tried before, unsuccessully, to fit them through Random Source panels.

I would recommend getting one of these

https://www.harborfreight.com/t-handle- ... 5AQAvD_BwE

Thank you, ordered. RS build doc recommend pots from thonk or tadya, going to give tadya a try this time, hopefully they fit without panel modification.

Still looking for 2x THAT2180A