DIY Trade Thread [ Parts, PCBs, Panels ]

From circuitbending to homebrew stompboxes & synths, keep the DIY spirit alive!

Moderators: Kent, luketeaford, Joe.

Post Reply
User avatar
synth.void
Common Wiggler
Posts: 232
Joined: Mon Jan 27, 2020 6:50 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by synth.void » Mon Nov 23, 2020 6:47 pm

efluon wrote:
Sat Nov 21, 2020 10:38 am
synth.void wrote:
Sat Nov 21, 2020 3:45 am
the bad producer wrote:
Fri Nov 13, 2020 9:42 am
I ordered some of these by mistake (wanted 1.3"):
128x64 OLED Module SPI 0.96"Graphic Displays,White on Black
Just realized I have a couple of them too. Any ideas where they could be used?
Pretty sure they work for the 1u versions of o&c and temps utile (will also be easy to use in your personal teensy adventure)
Great point, thanks. I've also realised I could make a rather simple scope with it.

DEEMARKAY
Common Wiggler
Posts: 72
Joined: Sat Aug 06, 2016 8:31 am
Location: germeny

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by DEEMARKAY » Tue Nov 24, 2020 5:55 am

synth.void wrote:
Mon Nov 23, 2020 6:47 pm
efluon wrote:
Sat Nov 21, 2020 10:38 am
synth.void wrote:
Sat Nov 21, 2020 3:45 am
the bad producer wrote:
Fri Nov 13, 2020 9:42 am
I ordered some of these by mistake (wanted 1.3"):
128x64 OLED Module SPI 0.96"Graphic Displays,White on Black
Just realized I have a couple of them too. Any ideas where they could be used?
Pretty sure they work for the 1u versions of o&c and temps utile (will also be easy to use in your personal teensy adventure)
Great point, thanks. I've also realised I could make a rather simple scope with it.
Yes, VPME Zeroscope also uses this part.
One needs to watch out though since there are versions with different numbers of pins and different pinouts.

User avatar
synth.void
Common Wiggler
Posts: 232
Joined: Mon Jan 27, 2020 6:50 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by synth.void » Tue Nov 24, 2020 7:31 am

DEEMARKAY wrote:
Tue Nov 24, 2020 5:55 am
One needs to watch out though since there are versions with different numbers of pins and different pinouts.
Yea, I went through the hell of launching a hello world with an Arduino and one of the screens. Pretty much trying out everything on the wiki page of u8g2. But it works!

kevin0
Common Wiggler
Posts: 52
Joined: Fri May 26, 2017 6:11 am

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by kevin0 » Sun Nov 29, 2020 1:49 pm

I have these PCBs to trade:

CGS/Serge - DUSG
CGS/Serge - VCS x 2
Stroh - FadeX4u

Looking for:

CGS/Serge: 1973 VCO
CGS/Serge: 1973 Filter x2
CGS/Serge: Router
CGS/Serge: W.A.D. ;)
CGS: Dual CV Processor

User avatar
Phetus
Wiggling with Experience
Posts: 295
Joined: Mon Mar 04, 2013 4:33 pm
Location: Berlin

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by Phetus » Tue Dec 01, 2020 8:25 am

looking for 4x 2180 B VCA chips incase anyone has any floating around...

User avatar
revtor
Dialing it in..
Posts: 2104
Joined: Sat Nov 29, 2008 10:31 am
Location: North Jerz

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by revtor » Tue Dec 01, 2020 6:13 pm

Phetus wrote:
Tue Dec 01, 2020 8:25 am
looking for 4x 2180 B VCA chips incase anyone has any floating around...
Phetus, I have a ton of the 2150’s. I’ll send you 4 for shipping cost if you want! Got any vca pcbs?
Steve
Fellow North Jersey Synthaholic

User avatar
revtor
Dialing it in..
Posts: 2104
Joined: Sat Nov 29, 2008 10:31 am
Location: North Jerz

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by revtor » Tue Dec 01, 2020 6:18 pm

PCB’s found

Looking for 4u..
CGS79 ring mod
CGS31 digital nois
e.

I’ve got a couple 4u (2”x6”) “blessed by Paul” MOTM 700 dual bidirectional switch pcbs for trade. Or cash.

Thanks
Steve
Fellow North Jersey Synthaholic

User avatar
Bamboombaps
Wiggling with Experience
Posts: 420
Joined: Wed Sep 16, 2015 7:14 am
Location: Glasgow

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by Bamboombaps » Tue Dec 08, 2020 8:52 am

Some blanks I have posted here before and some new ones
Looking for PCB panel sets
IMG_20201208_134636.jpg

User avatar
synth.void
Common Wiggler
Posts: 232
Joined: Mon Jan 27, 2020 6:50 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by synth.void » Mon Dec 28, 2020 1:34 am

Still looking for an o_C panel.

pjbulls
Common Wiggler
Posts: 227
Joined: Tue Feb 04, 2020 5:26 pm
Contact:

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by pjbulls » Mon Dec 28, 2020 7:13 am

Regular or micro? I have a few spare micro panels:

Image

They are blue & white though (as shown) so that may not be everyone's cup of tea :guinness:

User avatar
synth.void
Common Wiggler
Posts: 232
Joined: Mon Jan 27, 2020 6:50 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by synth.void » Mon Dec 28, 2020 7:19 am

pjbulls wrote:
Mon Dec 28, 2020 7:13 am
They are blue & white though (as shown) so that may not be everyone's cup of tea
Sorry, regular ones! But this one would look so good next to IOInstruments modules :sb:

User avatar
revtor
Dialing it in..
Posts: 2104
Joined: Sat Nov 29, 2008 10:31 am
Location: North Jerz

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by revtor » Mon Jan 04, 2021 12:43 pm

Ghielmetti 20x20 matrix gathering dust anyone? Looking. . .
Fellow North Jersey Synthaholic

User avatar
CliffordMilk
Wiggling with Experience
Posts: 357
Joined: Thu May 02, 2013 9:49 am
Location: Brighton, UK
Contact:

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by CliffordMilk » Thu Jan 07, 2021 5:31 am

Has anyone in the UK got a spare E-switch LP4OA1PBCTG ?

These are the illuminated switches used on Mutable Clouds. I ordered the wrong part from Mouser recently.

I ordered the wrong part from Mouser and have a whole load of parts and knobs I would happily trade - just tell me what you need.

User avatar
synthetek
Veteran Wiggler
Posts: 550
Joined: Fri Jun 05, 2015 3:32 am
Location: Orange County, California
Contact:

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by synthetek » Thu Jan 07, 2021 8:07 am

revtor wrote:
Mon Jan 04, 2021 12:43 pm
Ghielmetti 20x20 matrix gathering dust anyone? Looking. . .

Hi, I have a phutney clone pcb set so I think this matrix is what I need, what are you looking for?
Thanks

User avatar
revtor
Dialing it in..
Posts: 2104
Joined: Sat Nov 29, 2008 10:31 am
Location: North Jerz

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by revtor » Thu Jan 07, 2021 12:23 pm

synthetek wrote:
Thu Jan 07, 2021 8:07 am
revtor wrote:
Mon Jan 04, 2021 12:43 pm
Ghielmetti 20x20 matrix gathering dust anyone? Looking. . .

Hi, I have a phutney clone pcb set so I think this matrix is what I need, what are you looking for?
Thanks
I am looking to buy a matrix.
Thanks
Steve
Fellow North Jersey Synthaholic

User avatar
The_Elmo
1-Post Wiggler
Posts: 1
Joined: Tue Oct 13, 2020 9:33 am
Location: Finland

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by The_Elmo » Sun Jan 10, 2021 2:21 pm

CliffordMilk wrote:
Thu Jan 07, 2021 5:31 am
Has anyone in the UK got a spare E-switch LP4OA1PBCTG ?

These are the illuminated switches used on Mutable Clouds. I ordered the wrong part from Mouser recently.

I ordered the wrong part from Mouser and have a whole load of parts and knobs I would happily trade - just tell me what you need.
I have one extra, but I'm in Finland :confused:

I would need a couple of (two to be exact) STM32F103CBT6. The world seems to be out of them. I'd need them for my braids build.

User avatar
oberkorn
Veteran Wiggler
Posts: 651
Joined: Tue Jan 18, 2011 6:30 am
Location: Sweden, bork bork bork
Contact:

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by oberkorn » Sun Jan 10, 2021 3:18 pm

Looking for
Programmed FMogre dsp chip
Blue and White Rogan knobs for Maths MkI
Radio Music switches (any colour) "C&K D6R90"
35mm arcade knob(s), any colour
Chord Organ panel

Can trade with
Assembled Thomas Henry SN-Voice board (without ICs)
"Mutable" PCBs (1 Riddles, 1 Streams and 2 Slides, see pics further up in this thread
Black Mutable Plaits and Clouds panels
Music Thing Radio Music panel (Black)
VOID Modular 8hp blank panel
TiNRS Tuesday PCB/Panelset
ST Krach aus Strom PCB/Panel set
Music Thing Mikrophonie PCB
Clacktronics speaker PCB
Hepthaphasis LFO PCB
ST Eurokastle PCB
Pot chicklet PCBs
Fonik Attentuverter PCBs
you have to pay for the music but the noise is free

User avatar
B0bcat
Wiggling with Experience
Posts: 497
Joined: Sun Jun 10, 2018 9:07 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by B0bcat » Mon Jan 11, 2021 7:27 pm

Looking to buy the following (I'm in SoCal) -

2x Alpha potentiometer (Thonk style - other Alpha clones unfortunately do not fit the panel hole) B250K - Round shaft 6.35mm - Alpha Vertical 9mm Potentiometer - MPN: RD901F-40-15R1-B250K

2x THAT 2180 A

Hit me up!
Last edited by B0bcat on Thu Jan 14, 2021 10:30 am, edited 1 time in total.
WTB(US): Metasonix R-53, Bastl Softpop, Blippoo Box

User avatar
KittenVillage
Wiggling with Experience
Posts: 286
Joined: Sun Feb 17, 2019 10:30 am
Location: Glenshaw, PA
Contact:

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by KittenVillage » Mon Jan 11, 2021 10:29 pm

B0bcat wrote:
Mon Jan 11, 2021 7:27 pm
Looking to buy the following (I'm in SoCal) -

2x Alpha potentiometer (Thonk style - other Alpha clones unfortunately do not fit the panel hole)
Hey, not to be an ass at all, but are you talking about ones without a rotation tag? That tag is so very simple to snap off with needle nose pliers that it's trivial to do. AFAIK no one but Thonk has ones without the rotation tag. Since you are in S. Cal, you may find that https://www.tubesandmore.com/ would ship fastest and cheapest to you. I think they are in Tempe, AZ.

I think you can find the THAT 2180A at mouser, but it's pricey.


Eurorack is an exercise in delayed desire.

User avatar
B0bcat
Wiggling with Experience
Posts: 497
Joined: Sun Jun 10, 2018 9:07 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by B0bcat » Mon Jan 11, 2021 10:40 pm

KittenVillage wrote:
Mon Jan 11, 2021 10:29 pm
B0bcat wrote:
Mon Jan 11, 2021 7:27 pm
Looking to buy the following (I'm in SoCal) -

2x Alpha potentiometer (Thonk style - other Alpha clones unfortunately do not fit the panel hole)
Hey, not to be an ass at all, but are you talking about ones without a rotation tag? That tag is so very simple to snap off with needle nose pliers that it's trivial to do. AFAIK no one but Thonk has ones without the rotation tag. Since you are in S. Cal, you may find that https://www.tubesandmore.com/ would ship fastest and cheapest to you. I think they are in Tempe, AZ.

I think you can find the THAT 2180A at mouser, but it's pricey.
Thanks - rotation tag or not doesn't matter, but there are "fake" Alpha pots that look fairly similar to the Thonk ones but have a slightly larger shaft diameter. I've tried before, unsuccessully, to fit them through Random Source panels.

The ones on Tubesandmore, at least on the photos, look like the non-fitting ones.

Re: THAT chips, they're out of stock at Mouser, ETA March or May or 50 weeks.
WTB(US): Metasonix R-53, Bastl Softpop, Blippoo Box

User avatar
elmegil
Super Deluxe Wiggler
Posts: 3038
Joined: Sun Apr 29, 2012 2:57 pm
Location: Chicago

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by elmegil » Mon Jan 11, 2021 10:46 pm

B0bcat wrote:
Mon Jan 11, 2021 10:40 pm
Thanks - rotation tag or not doesn't matter, but there are "fake" Alpha pots that look fairly similar to the Thonk ones but have a slightly larger shaft diameter. I've tried before, unsuccessully, to fit them through Random Source panels.

I would recommend getting one of these

https://www.harborfreight.com/t-handle- ... 5AQAvD_BwE

User avatar
B0bcat
Wiggling with Experience
Posts: 497
Joined: Sun Jun 10, 2018 9:07 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by B0bcat » Tue Jan 12, 2021 3:58 pm

elmegil wrote:
Mon Jan 11, 2021 10:46 pm
B0bcat wrote:
Mon Jan 11, 2021 10:40 pm
Thanks - rotation tag or not doesn't matter, but there are "fake" Alpha pots that look fairly similar to the Thonk ones but have a slightly larger shaft diameter. I've tried before, unsuccessully, to fit them through Random Source panels.

I would recommend getting one of these

https://www.harborfreight.com/t-handle- ... 5AQAvD_BwE
Thank you, ordered. RS build doc recommend pots from thonk or tadya, going to give tadya a try this time, hopefully they fit without panel modification.

Still looking for 2x THAT2180A
WTB(US): Metasonix R-53, Bastl Softpop, Blippoo Box

User avatar
jersupereq
Wiggling with Experience
Posts: 265
Joined: Sat Aug 16, 2008 9:24 pm
Location: PDX

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by jersupereq » Thu Jan 28, 2021 2:31 pm

B0bcat wrote:
Tue Jan 12, 2021 3:58 pm
Thank you, ordered. RS build doc recommend pots from thonk or tadya, going to give tadya a try this time, hopefully they fit without panel modification.

Still looking for 2x THAT2180A
Last 2 available: https://www.newark.com/that-corporation ... dp/50M5189
Those things are pretty much sold out everywhere

User avatar
B0bcat
Wiggling with Experience
Posts: 497
Joined: Sun Jun 10, 2018 9:07 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by B0bcat » Thu Jan 28, 2021 2:35 pm

jersupereq wrote:
Thu Jan 28, 2021 2:31 pm
B0bcat wrote:
Tue Jan 12, 2021 3:58 pm
Thank you, ordered. RS build doc recommend pots from thonk or tadya, going to give tadya a try this time, hopefully they fit without panel modification.

Still looking for 2x THAT2180A
Last 2 available: https://www.newark.com/that-corporation ... dp/50M5189
Those things are pretty much sold out everywhere
Thanks, I ordered them a month ago when they also showed two in stock, and then I got an estimated shipment update for mid March. I think their stock status is not represented truthfully, or in the best way they could
WTB(US): Metasonix R-53, Bastl Softpop, Blippoo Box

User avatar
synth.void
Common Wiggler
Posts: 232
Joined: Mon Jan 27, 2020 6:50 pm

Re: DIY Trade Thread [ Parts, PCBs, Panels ]

Post by synth.void » Sat Jan 30, 2021 7:17 am

Lookin for the monsoon LEDs (common cathode r/g, like https://www.mouser.de/ProductDetail/Kin ... WP115VEGW/). Anyone in EU/Berlin?

Post Reply

Return to “Music Tech DIY”