Plague Bearer tips and tricks?

Gear, Suggestions and Discussion.

Moderators: Kent, computer controlled, flight

Post Reply
User avatar
sixteen
Wiggling with Experience
Posts: 306
Joined: Wed May 25, 2011 11:19 am
Location: London

Plague Bearer tips and tricks?

Post by sixteen » Tue May 01, 2012 8:05 am

Hello Wigglers.

I got a PB a few months back and its the one module I tend not to use, I generally like it and always try to keep it in the patch but in the end I normally remove it from the chain,

I want to use it with basses, leads and percussions for dance floor stuff.

I understand it quite delicate so I keep a uatt sitting beside it, Here's some of the other modules I'm using with it.

2dixes
z3000
submix7
maths
rene
corgo
opto
hex vca
phongene
tiptop808 kik&snr
A-199 spring verb...
SCM

How are u guys using it?

I suppose I'm just looking for some inspiration here...

Nice one

Sixteen

User avatar
Repeater
Phantom Powers
Posts: 765
Joined: Sun Oct 03, 2010 3:14 am
Location: Rochester, NY

Post by Repeater » Tue May 01, 2012 11:00 am

I find I get much better results when I don't patch it with expectations. I didn't click with it until I stopped thinking about it as a filter/audio processor. The two things I'd say are experiment with attenuating/overloading all of the inputs and feeding audio in the CV inputs and CV into the audio inputs. I mostly use it for feedback patches, FM and as an audio source.

User avatar
lorenzovektor
I want cyborg legs
Posts: 791
Joined: Mon Feb 07, 2011 2:07 am
Location: Chicago

Post by lorenzovektor » Tue May 01, 2012 12:24 pm

the Plague really come alive when you throw CV into it.

User avatar
nooneimportant
Common Wiggler
Posts: 152
Joined: Wed Mar 14, 2012 2:13 pm

Post by nooneimportant » Tue May 01, 2012 12:41 pm

Yeah try to not really use it as a "filter", though you can. Also it responds a bit better if you don't send a very loud signal to it. The new models have attenuation built in which is really nice.

User avatar
Mefistophelees
USB Cat
Posts: 1092
Joined: Sat Feb 04, 2012 4:30 pm
Location: UK

Post by Mefistophelees » Tue May 01, 2012 3:16 pm

Read the manual.

No really... I had much the same problem until I read the manual. It doesn't say that much but what it does say is a very good starting point.

It's a module you have to really play around with to get the best out of and it can be pretty impressive.

http://www.flightofharmony.com/?page_id=22

User avatar
boramx
lepidopteran orgasm
Posts: 2164
Joined: Sat Mar 20, 2010 12:02 pm
Location: Infant Island

Post by boramx » Tue May 01, 2012 3:27 pm

Take your osc tri out in pb then stick it back into the osc's expo input. Monitor the sine out tune to taste.

Pretty sweet in a sequence.

User avatar
vav
Beer Master
Posts: 3406
Joined: Sun Apr 19, 2009 10:01 am
Location: Chicago

Post by vav » Tue May 01, 2012 5:54 pm

Through anything CV through an attenuator and tweak SOFTLY! The PB has a LOADS of range if you move slowly!
Vactrols are the electronic equivalent of being drunk. -decaying.sine

User avatar
mhtones
Dreams in CV
Posts: 1616
Joined: Fri Aug 21, 2009 12:18 pm
Location: SF Bay Area

Post by mhtones » Wed May 02, 2012 1:09 am

vav wrote:Through anything CV through an attenuator and tweak SOFTLY! The PB has a LOADS of range if you move slowly!
+1 Very Softly/Slowly!

I mentioned this in another thread, but I totally rediscovered my PB when I added a Choices joystick to my setup. The joystick allows you to really dial in the sweet spots easily and then move slowly through them simultaneously adjusting 2 parameters (since joystick control has x/y versus single knob tweaking). Since Choices has scale adjustments for both x/y outputs, you can really get precise control of the PB inputs. Throw in a feedback loop on the PB and I've gotten some lovely morphing tones.
FS (US): Dixie 2, Malekko IMIX

User avatar
sixteen
Wiggling with Experience
Posts: 306
Joined: Wed May 25, 2011 11:19 am
Location: London

Post by sixteen » Wed May 02, 2012 4:02 am

Thanks for all the tips guys,

Ill go threw them all this evening...

Sorry I posted this is the wrong place...

Six

User avatar
computer controlled
Super Deluxe Wiggler
Posts: 3844
Joined: Sun May 31, 2009 4:16 pm
Location: Seattle, WA

Post by computer controlled » Wed May 02, 2012 2:13 pm

There are a ton of sweet spots in the PB. Don't go wild with tweaking, just take your time and listen. Go easy on the Inputs as well, you don't need them very loud.
Stuff: SH-01A . TR-8S . MX-1 . D-20 . Waldorf MicroQ . Ensoniq EPS 16+ . Yamaha MODX6 . Yamaha DX7 . MPC Live . Avalon BassLine . Behringer Neutron . Behringer MS-101 . Behringer Pro-1 . Behringer K-2 . Behringer TD-3 . E-Mu Emax . E-Mu Emax II . BeatStep Pro . Keystep .

User avatar
JJ
Veteran Wiggler
Posts: 631
Joined: Sat May 08, 2010 10:46 am
Location: Turku, Finland, EU

Post by JJ » Sat May 26, 2012 11:51 am

What everyone above said about sweetspots & attenuators.

Another thing I like to do is split the signal with active multiples and feed the split into PB and then mix it back with the original trough a bipolar mixer.

User avatar
lilakmonoke
Super Deluxe Wiggler
Posts: 2755
Joined: Thu Oct 21, 2010 6:18 am
Location: berlin

Post by lilakmonoke » Wed Jun 13, 2012 4:51 pm

if you want to go to distortion land do this: take two different sequences tri or sine waves and mix them in something that saturates or clips (corgo or stg.mix) feed that into the PB.

the "electric guitar" in this track was done like that:

http://tindeck.com/listen/nnys

.
.

User avatar
DanielW
Ultra Wiggler
Posts: 758
Joined: Mon Oct 26, 2009 3:02 am
Location: Stockholm, Sweden

Post by DanielW » Thu Jul 05, 2012 4:58 pm

Get another PB, patch audio out from one into the other, then audio out from the other into the first, then audio out from the first into the second, then the last audio out into the Corgasmatron. Tweak all knobs, feed them CV and listen to the Plague Bearers come alive without any external input.

Post Reply

Return to “Flight of Harmony”