Oops My Cable -- How to mend a banana (cable)

Modular and other sound devices from BugBrand.

Moderators: Kent, BugBrand

Post Reply
User avatar
BugBrand
Knowledge of Bugs
Posts: 7258
Joined: Tue Jul 15, 2008 11:59 am

Oops My Cable -- How to mend a banana (cable)

Post by BugBrand » Mon Jan 10, 2011 6:46 am

Sometimes the wire comes out of the banana plug - argh!
But it is quick and easy to repair!


Image
Tools required - one small flathead screwdriver and a pair of wire-strippers


Image
You will notice two little rectangular holes on the side - use the screwdriver to depress these nubs and flip out the top part.


Image
You can then slide out the metal part.

Image
Inside the metal part is a little threaded set-screw - you can see it through the side window (where the wire will go). Put the screwdriver into the top of the metal part and locate the screw terminal. Unscrew it to open up the side hole.


Image
Use the wire strippers to strip a short length on the end of the wire, then insert it into the side-hole.


Image
Tighten to attach. Trim off any excess from the other side of the side hole.

Image
Re-insert the metal part and close the little plastic flap.

Job Done!
Last edited by BugBrand on Mon Jan 10, 2011 4:57 pm, edited 1 time in total.

User avatar
miditerranean
Veteran Wiggler
Posts: 745
Joined: Fri May 01, 2009 11:49 am
Location: minneapolis

Post by miditerranean » Mon Jan 10, 2011 4:32 pm

Hasn't happened to me yet but I'm saving this thread for future reference, thanks Tom!

User avatar
emergencyofstate
Synthesist
Posts: 1702
Joined: Fri Mar 13, 2009 3:50 pm
Location: San Diego, CA

Post by emergencyofstate » Sun Jan 23, 2011 10:20 pm

Thanks for this Tom. I just repaired three of my cables and it took less than 10 minutes!

User avatar
lud
Super Deluxe Wiggler
Posts: 1134
Joined: Tue May 05, 2015 2:02 pm
Location: UK

Post by lud » Wed Feb 14, 2018 2:20 pm

Thanks a lot for this handy little post, didn't realise it was so easy and solder-free to put together a Rapid banana cable :nana: :banana: :bananaguitar:

User avatar
Flexyflier
Common Wiggler
Posts: 126
Joined: Thu Oct 30, 2014 12:11 am

Post by Flexyflier » Fri Dec 07, 2018 10:45 pm

had a Phenol,that was my banana plug experience,but going to order some cables from Tom
I also have a makenoise jumbler and one from Tony at Synovatron......Euro to banana.
http://synovatron.blogspot.com
"Drowning...................not waving!"

User avatar
Kafgee
Common Wiggler
Posts: 102
Joined: Fri May 16, 2014 3:34 pm
Location: Athens

Post by Kafgee » Sun Jan 13, 2019 8:59 pm

What do you do when just the tip comes off ?

User avatar
BugBrand
Knowledge of Bugs
Posts: 7258
Joined: Tue Jul 15, 2008 11:59 am

Post by BugBrand » Mon Jan 14, 2019 2:30 am

Do you mean the little round tip - c. 3mm long piece right on the end?
If so, unfortunately I think the whole end should be replaced.

castano
Learning to Wiggle
Posts: 41
Joined: Sun Apr 10, 2016 5:36 pm

Post by castano » Sun Jun 09, 2019 3:06 pm

Does anyone know where I can order those banana plug ends to make my own cables?

User avatar
lud
Super Deluxe Wiggler
Posts: 1134
Joined: Tue May 05, 2015 2:02 pm
Location: UK

Post by lud » Sun Jun 09, 2019 3:27 pm

You can get the 4mm plugs and wire in different colours at Rapid electronics online :banana:

castano
Learning to Wiggle
Posts: 41
Joined: Sun Apr 10, 2016 5:36 pm

Post by castano » Thu Jun 13, 2019 4:56 pm

Thanks for the info! :)

Post Reply

Return to “BugBrand Devices”