DAY 3: VCA Quintet Mixing Console

DickMarker · Post by **DickMarker** » Thu Mar 05, 2015 12:49 pm

Cheers for the response - I just noticed you've kindly answered that question twice now in this thread!

flo · Post by **flo** » Thu Mar 05, 2015 1:07 pm

My pleasure

MATSmile · Post by **MATSmile** » Sat Apr 25, 2015 5:46 pm

Does anyone know who deep is the module? It says 50mm deep on site, but does it include pin attached to it? I have exactly 50mm deep case, want to try to fit it in.

kla4spieler · Post by **kla4spieler** » Wed Nov 25, 2015 7:15 pm

Are the 802 pots bolted on the panel?

Summa · Post by **Summa** » Thu Nov 26, 2015 3:55 pm

MATSmile wrote:Does anyone know who deep is the module? It says 50mm deep on site, but does it include pin attached to it? I have exactly 50mm deep case, want to try to fit it in.

saw this now, it's 53mm deep so sorry it won't fit (I updated the MG spec's a couple of years ago due to this.

Summa · Post by **Summa** » Thu Nov 26, 2015 3:57 pm

kla4spieler wrote:Are the 802 pots bolted on the panel?

nope, but they're stiff and nice..

Bark · Post by **Bark** » Sun Apr 03, 2016 4:23 am

Hi guys!

I just bought a 802, and saw this reversed panel on MG. Any of you guys using this? How did you obtain it? I can't seem to find it on the Addac site...

Would be nice to have this, mounting the module in a lower row in my case...

Cheers!

cloudleft · Post by **cloudleft** » Wed Aug 08, 2018 10:30 pm

Summa wrote:
MATSmile wrote:Does anyone know who deep is the module? It says 50mm deep on site, but does it include pin attached to it? I have exactly 50mm deep case, want to try to fit it in.
saw this now, it's 53mm deep so sorry it won't fit (I updated the MG spec's a couple of years ago due to this.

The ADDAC site lists the depth as 55mm... so how deep is it actually? My case is exactly 56mm but I'm wondering if maybe just maybe I can sneak the ribbon cable under that last millimeter?

I know this is an old thread, but this seemed the best place to ask! Thanks.

Post by **Paranormal Patroler** » Thu Aug 09, 2018 3:57 pm

I'd go with what the ADDAC site says.

cloudleft · Post by **cloudleft** » Mon Aug 20, 2018 2:31 pm

Just racked my new 802 from Analogue Haven, and there's plenty of room beneath. Luckily, I was mis-measuring my case dimensions.

Man this thing sounds good!

disquiet · Post by **disquiet** » Fri Sep 21, 2018 11:55 am

__ag wrote:The Solo line is also intended for Pre Listening purposes, using this output to connect your headphones through some headphone amplifier module.

My naive question of the moment: is it a problem to plug a headphone directly into the solo out (either by channel or the Solos Out jack)? I imagine it would be, even with the volume on the low end.

Summa · Post by **Summa** » Fri Sep 21, 2018 3:10 pm

disquiet wrote:
__ag wrote:The Solo line is also intended for Pre Listening purposes, using this output to connect your headphones through some headphone amplifier module.
My naive question of the moment: is it a problem to plug a headphone directly into the solo out (either by channel or the Solos Out jack)? I imagine it would be, even with the volume on the low end.

You mean plugging a Hot Eurorack signal, that's mono through the headphones instead of a Line level signal that's balanced stereo, what can go wrong?

disquiet · Post by **disquiet** » Fri Sep 21, 2018 3:21 pm

Summa wrote:You mean plugging a Hot Eurorack signal, that's mono through the headphones instead of a Line level signal that's balanced stereo, what can go wrong?

Thanks for confirming. I figured.

I know I can get something like a Rosie to give me cue options. Alternately, I was wondering if there's a passive connector that could be put between a headphone and an ADDAC mixer out that would do the job.

MUFF WIGGLER

MUFF WIGGLER

DAY 3: VCA Quintet Mixing Console

Re: DAY 3: VCA Quintet Mixing Console

Re: DAY 3: VCA Quintet Mixing Console

Re: DAY 3: VCA Quintet Mixing Console