MUFF WIGGLER Forum Index
 FAQ & Terms of UseFAQ & Terms Of Use   Wiggler RadioMW Radio   Muff Wiggler TwitterTwitter   Support the site @ PatreonPatreon 
 SearchSearch   RegisterSign up   Log inLog in 
WIGGLING 'LITE' IN GUEST MODE

TWO59 VCO (by FEEDBACK) (added new FM demo)
MUFF WIGGLER Forum Index -> Eurorack Modules  
Author TWO59 VCO (by FEEDBACK) (added new FM demo)
strat-1
You cn find the module at : www.feedbackmodules.com

The TWO59 is an accurate recreation in EURORACK format of the VCO/LFO section of the most sought after vintage west coast complex oscillator.
Because of the triangle core, the VCO's work very well for FM modulation.

TWO59 is not a clone of the original 259, but an enhanced adaptation of the classic circuit to eurorack format with many additional features.
-4 independent buffered outputs that can be used simultaneously with the shaper module
-a more stable core, with a better V/oct tracking up to 5octaves
-each oscillator can be phased locked (hard synced)

For DIY version and more technical informations visit the DIY thread :
https://www.muffwiggler.com/forum/viewtopic.php?t=169990

Cost for one VCO : 128EUR (5pcs. in stock)


DISCLAIMER : It's possible you will need to recalibrate the V/OCT trimmer when you receive the module. All the hard calibration is done,
but V/OCT calibration depends on the exact voltage of your power source and your midi to cv, cv sequencer module.
For this you will need a tuner (hardware or software). You will receive a document describing the procedure.





Audio demos :

The sound clicks are from computer latency, not from the modules smile
Somehow I forgot to record the ramp wave. I will record it soon.

[s]https://soundcloud.com/strat1/two59-square[/s]
[s]https://soundcloud.com/strat1/two59-triangle[/s]
 [s]https://soundcloud.com/strat1/two59-sine[/s]
[s]https://soundcloud.com/strat1/two59-fm-capabilities[/s]

Other FEEDBACK built modules you can purchase.

106 Chorus : 150EUR
https://www.muffwiggler.com/forum/viewtopic.php?t=166892
CP3+ Mixer : 70EUR
https://www.muffwiggler.com/forum/viewtopic.php?t=158439
SmArTT verter : 50EUR
https://www.muffwiggler.com/forum/viewtopic.php?t=158691
PRE CR : 70EUR
https://www.muffwiggler.com/forum/viewtopic.php?t=163228
PRE BX : 70EUR
https://www.muffwiggler.com/forum/viewtopic.php?t=163224
PRE KM : 70EUR
https://www.muffwiggler.com/forum/viewtopic.php?t=163227
brandonlogic
im going to be building this very soon. very excited.
i was curious who has this already, and how users think it compares to other 259 like complex oscillators like the verbos, sputnik, endorphin, make noise, etc.

brandonlogic
checking back to see if there are any users here of this osc!?
surprising there isn't more mention of this vco seeing the full build (2vco's+shaper) it a contender of the other popular buchla inspired complex vcos.
interested to see how it compares.
finally ordered all my parts, not a cheap build! I'll make sure to do a youtube video demonstrating how it sounds once i finish the build, since there isnt much out there yet.
DonKartofflo
brandonlogic wrote:
checking back to see if there are any users here of this osc!?
surprising there isn't more mention of this vco seeing the full build (2vco's+shaper) it a contender of the other popular buchla inspired complex vcos.
interested to see how it compares.
finally ordered all my parts, not a cheap build! I'll make sure to do a youtube video demonstrating how it sounds once i finish the build, since there isnt much out there yet.


Please do! Curious myself..
brickman
Is the Shaper going to be available as an assembled module ?
afterswish
Bear with me, I'm sure this is obvious if you know what you're doing (I don't!) but:

>>> What is the 'CV IN' input for? hmmm.....

I assume 'KEY CV' is the 1v/octave input, and 'FM IN' is self explanatory.




(P.S. would it be possible to upload a sound example of the hard sync plus a little wiggling of the lock gain please?)
brandonlogic
Divkid is going to be doing a demo for this! Hopefully soon.. Excited! applause applause applause
strat-1
I recorded a short demo to demonstrate the FM capabilities of TWO59 VCO.
I fed another type of VCO (system-X VCO) into the FM input of TWO59.
In recording you will hear in this order :
- sine output of TWO59 with saw as FM modulator,
- triangle output of TWO59 with triangle as FM modulator,
- square output (octave notes) with arp on FM modulator,
- saw output (octave notes) with arp on FM modulator.

[s]https://soundcloud.com/strat1/two59-fm-capabilities[/s]
brandonlogic
finaly got my full two59 complex osc setup up and running (two vcos + shaper), havnt spent to much time with it but so far im gettting some nice sounds out of it!
my first couple tests:
https://www.instagram.com/p/BVV-umClFg0
https://www.instagram.com/p/BVYQsbFlkws

more to come soon!
jschussler
I'll second the question "what is the 'CV in' input for?" I'm trying different things with mine, not getting obvious results....
Hansi026
Hi,

is the TWO59 VCO on there website full assembled for 128 € ?
Two of them and a TWO59 SHAPER, should be an good combo.

who has experience with this modules ?

cheers
Hansi
brandonlogic
a quick little raw two59 complex osc config demo
tasun
First normal demo, thanks!
I have just one vco, was thinking about building the shaper as well but it looks kinda scary to build it.. smile

brandonlogic wrote:
a quick little raw two59 complex osc config demo
brandonlogic
another demo,
recorded straight form the main shaper's output.

[soundcloud url="https://api.soundcloud.com/tracks/366508589" params="auto_play=false&hide_related=false&show_comments=true&show_use r=true&show_reposts=false&visual=true" width="100%" height="450" iframe="true" /]
MUFF WIGGLER Forum Index -> Eurorack Modules  
Page 1 of 1
Powered by phpBB © phpBB Group