Unreleased Richter Designs - Pulse Farm

Discussion and support for Wiard Products

Moderators: Kent, grantrichter, carygrace

User avatar
BananaPlug
Super Deluxe Wiggler
Posts: 2529
Joined: Wed Dec 05, 2007 10:37 pm
Location: PHL USA

Re: Unreleased Richter Designs - Pulse Farm

Post by BananaPlug » Thu Feb 13, 2020 8:26 am

Interested but would like to clarify some basics. I’d prefer to build it as frac with bananas. You mentioned depth. Looks like one pcb so what’s the concern? Thanks for reviving this thing.

User avatar
vladosh
Learning to Wiggle
Posts: 41
Joined: Sun Sep 08, 2013 5:54 am
Contact:

Re: Unreleased Richter Designs - Pulse Farm

Post by vladosh » Thu Feb 13, 2020 9:38 am

what i built for myself is 2 pcb's the bigger is 130x90mm ,it's really rough comparing to what people do in eagle but it works for me .. as the jacks are not pcb mounted it's really bunch of wires ,i mount my pcb's with L brackets so it's 90mm inside the case as my synth is 4U

User avatar
vladosh
Learning to Wiggle
Posts: 41
Joined: Sun Sep 08, 2013 5:54 am
Contact:

Re: Unreleased Richter Designs - Pulse Farm

Post by vladosh » Thu Feb 13, 2020 9:58 am

i can imagine it for frack rack as a bit wider module 28hp seems good to sandwich the pcb's directly to the panel ,there should be space to add something useful as pulse delay or additional divides or patterns to use with the neurons

User avatar
vladosh
Learning to Wiggle
Posts: 41
Joined: Sun Sep 08, 2013 5:54 am
Contact:

Re: Unreleased Richter Designs - Pulse Farm

Post by vladosh » Thu Feb 13, 2020 11:31 am

here's a panel for this as the panel from Richter's page didn't have the pattern gen included ,and in addition to that i added Varilogic II on the same panel ,these schematics should somewhat work with 12V but i'm not sure so - in 3U format plus a silly graphic that suppose to remind of the wonderful artwork of Wiard modules
You do not have the required permissions to view the files attached to this post.

User avatar
sabasan
Common Wiggler
Posts: 168
Joined: Fri Jul 25, 2008 4:42 am

Re: Unreleased Richter Designs - Pulse Farm

Post by sabasan » Wed Feb 19, 2020 2:42 am

nice .

User avatar
diophantine
Super Deluxe Wiggler
Posts: 2251
Joined: Mon Jan 10, 2011 2:50 pm
Location: San Diego, CA, USA

Re: Unreleased Richter Designs - Pulse Farm

Post by diophantine » Fri Feb 21, 2020 8:12 pm

I'd be interested in a few of these PCBs...

A few questions...

Is the "clock" jack the "whole note" output? Or did you figure out a nifty way to get an external clock input?

I assume that there's DIP switches on the PCBs for the pattern outputs?

I notice on your panel designs you omit the '0' position (n/c) for the cell threshold... is it just not marked, or did you find that threshold setting to be uninteresting?

Thanks!!

User avatar
aethyr
Common Wiggler
Posts: 229
Joined: Fri May 23, 2014 5:45 pm
Location: Over the edges

Re: Unreleased Richter Designs - Pulse Farm

Post by aethyr » Fri Feb 21, 2020 8:34 pm

I would like one too
chachi wrote:
Thu Jan 30, 2020 10:39 pm
i would get in on a pcb run if possible, depth and 15v no problem.

User avatar
vladosh
Learning to Wiggle
Posts: 41
Joined: Sun Sep 08, 2013 5:54 am
Contact:

Re: Unreleased Richter Designs - Pulse Farm

Post by vladosh » Sat Feb 22, 2020 11:41 am

the switches are 3 position with middle off ,i use that too ,on the pcb with dividers and patterns there are dip switches to select pattern it can do without them of course if you know what pattern is for you ,and clock output is useful to drive other standard sequencers to be in sync with this one ,you can look at this also as master clock ,and i thought it would be nice to be able to sync this clock with external but i never did that ,should be easy it's just 555 ,and i'm not thinking to offer pcb's for this ,however if anyone wants one with 15V PSU i can make for you ,depth is not a problem it can be around 50mm

Post Reply

Return to “Wiard”