MUFF WIGGLER Forum Index
 FAQ & Terms of UseFAQ & Terms Of Use   Wiggler RadioMW Radio   Muff Wiggler TwitterTwitter   Support the site @ PatreonPatreon 
 SearchSearch   RegisterSign up   Log inLog in 
WIGGLING 'LITE' IN GUEST MODE

[IN STOCK] E.A.S. "miss 10" LFO/Noise/S&H v2.0
MUFF WIGGLER Forum Index -> Music Tech DIY Goto page 1, 2, 3, 4  Next [all]
Author [IN STOCK] E.A.S. "miss 10" LFO/Noise/S&H v2.0
E.A.S.
Hey guys and gals,

Ive had a few emails regarding the LFO, Noise, S&H pcb I released a bit ago, So ive decided to do another run, this time a little nicer.

This time the size is substantially smaller. 37% smaller.
The size is now the same size as the new HADSR board, the VCO v2.0, and the VCF/A v2.0 PCB.

4.3" x 1.4"

A perfect size to sit parallel behind the panel sold by negativspace .

-M

---------------------------------
Inputs / Outputs / Controls
---------------------------------
LFO

Speed Pot- sets the modulation frequency.

Skew Pot-
Sweeps the 'Triangular' output from saw at one extreme, to triangle in Mid position, to a Ramp wave at the other extreme.
At the same time this pot also sweeps the PW ratio on the 'rectangular' output.

Triangular Output- saw thru, triangle thru,
ramp. set by Skew Pot.

Rectangular Output-
90% on 10% off, thru 10% on thru 90% off- set by Skew Pot.

--------------------------------

Sample and Hold (actually a Track and Hold)

Signal Input- signal to be Tracked, sampled and Held.

Trigger/gate input-Use this input to instigate the track, sample, and hold. This input has a comparator on it, so it can accept a large variety of signals.
A gate on this input will cause the Signal input to pass thru to the output unaffected as long as the Gate remains HIGH.
When the Gate goes LOW the output will "hold" at the voltage that was present on the signal input until a new gate/trigger is applied.
A short pulse on this input will cause the unit to act more like a traditional sample and hold.

S/H output- Outputs input signal when Gate/Trigger is HIGH. Outputs CV of sampled signal when gate/trigger goes LOW.
---------------------------------
NOISE!!!

Pink Output- Pink filtered Noise.

White Output- White Noise! pshh

---------------------------------

Price for these are $25 ea. shipping included.

Payment via paypal to Michael (dot) Alan (dot) Schmidt [at] Gmail [dot] com


---------------------------------
PCB Preview
---------------------------------
NOISE/SH/LFO 2.0 PCB by itsfatmike, on Flickr


----------------------------------
Wiring diagram
----------------------------------

Lfo/n/t&h 2.0 wiring diagram by itsfatmike, on Flickr

-------------------------------------
B.O.M.
-------------------------------------

C1.....10uf/16v................647-USA1C100MDD
C2.....1uf/50v..................647-UMA1H010MDD
C3.....47p........................505-FKP247/1000/10
C4.....10uf/16v.................647-USA1C100MDD
C5.....0.022uf...................505-MKP2G022201E00MS
C6.....0.1 uf.....................505-MKS2.1/63/10
C7.....1uf np.....................505-MKS2C041001FKI00
C8.....0.1 uf......................505-MKS2.1/63/10
C9.....0.1 uf........................505-MKS2.1/63/10
C10.....10uf/16v.................647-USA1C100MDD
C11.....10uf/16v.................647-USA1C100MDD

D1.....1N4148................583-1N4148-T
D2.....1N4148................583-1N4148-T
D3.....1N4148...............583-1N4148-T
D4.....LED......................604-WP7113ID5V
D5.....1N4148..............583-1N4148-T
D6.....1N4148...............583-1N4148-T
D7.....1N4148..............583-1N4148-T
IC1.....LM4558...............595-RC4558P
IC2.....LM4558................595-RC4558P
IC3.....TL071....................595-TL071CP
IC4.....LM4558................595-RC4558P

Q1.....2N3904............512-2N3904TF
Q2.....2N3904..............512-2N3904TF
Q3.....J111......................512-J111D26Z

for resistors use mouser part
# 271-xxx-RC , where "xxx" is value listed below.

R1.....100K
R2.....1M
R3.....2.2M
R4.....10K
R5.....1K
R6.....6.8K
R7.....220K
R8.....1K
R9.....100k
R10.....10k
R11.....470
R12.....220k
R13.....100k
R14.....10k
R15.....10k
R16.....1k
R17.....1M
R18.....1k
R19.....1k
R20.....3.3K
R21.....20K
R22.....1K
R23.....100K
R24.....4.7K
R25.....4.3K
R26.....2.7K
R27.....4.7K

VR1.....100K TRIM.....858-64WR100KLF
VR2.....10k TRIM.....858-64WR10KLF

VR3.....100KB.....313-1000F-100K
VR4.....10KB.....313-1000F-10K

-Thanks for looking!

-Mike
woodster
Just ordered one of these PCB's.
Now need to grab a panel!
sammy123
Cool. I am interested.
NS4W
Where's the panel thread again? (Muffs search engine is not cooperating)
woodster
I can't remember where it was, but I got a panel from negativespace.
Drop him a line to see if he has any spares...
widdly
https://www.muffwiggler.com/forum/viewtopic.php?t=54556


If you want to search on muffs you can type in Google...

Site:muffwiggler.com what you wanna search
negativspace
I'm out of spares.

I can reorder, though, if there are at least 30 takers or so. thumbs up
Randy
I ordered one PCB as well, and I'm interested in a panel.

Randy
NS4W
Thanks! I have the panel, was just looking for extra info on the build. w00t
Randy
Being new at this, is there a build thread?

Randy
Randy
I'm wondering if I can do this in 6hp?



Randy
woodster
I'm wondering if orders for this PCB will ever get delivered ?

seriously, i just don't get it
Randy
Anyone know if these were shipped yet?
woodster
Not as of yet.
I did get word back from Mike at E.A.S. (thumbs up) who apologised for the delay and said they will ship at some point soon.
Now I need to find a euro panel for this PCB.
blandoon
I whacked together a quick Frac panel for it in FPExpress, loosely based on the Euro panel that was shown for the 1.0 board. Mike did say the 2.0 board will work fine on +-15v, despite not having the MOTM style power header.
blandoon
Any update on this?

Not trying to be That Guy, and it's not like I have time to finish the build right this second lol Just curious where it stands, really.
Randy
Me too!

Randy
Randy
A bit of communication can go a long way towards alleviating potential disappointment and bad feelings.

In other words, WTF happened to these!?

Randy
Randy
Okay, so has this guy decided to give up his normal life and buy a small bar on a deserted beach in the tropics somewhere?

Randy
E.A.S.
Randy wrote:
Okay, so has this guy decided to give up his normal life and buy a small bar on a deserted beach in the tropics somewhere?

Randy


Hey guys,
I totally dropped the ball on ordering these. That said they have been orrdered and will be getting in next week. (and the HADSR soon after)

I feel really bad about the extremely long wait time, so, to anyone who has paid these already, I'd like to offer you a small token, your choice of either an MS-10 VCF/A PCB, or the MS-50 VCO PCB. PM me with your choice of and i'll send it out with your LFO order.

Thanks!

-Mike
woodster
I really am an optimist at heart, but an 8 month wait for PCB's is just plain ridiculous.
I do still hold out hope that Mike gets these outstanding Miss10 PCB's out to people who paid for them.
Thursday October 24th 2013 was when I paid for an LFO/S&H/Noise PCB and also a HADSR PCB...

Dead Banana
E.A.S.
woodster wrote:
I really am an optimist at heart, but an 8 month wait for PCB's is just plain ridiculous.
I do still hold out hope that Mike gets these outstanding Miss10 PCB's out to people who paid for them.
Thursday October 24th 2013 was when I paid for an LFO/S&H/Noise PCB and also a HADSR PCB...

Dead Banana


See previous post. thumbs up
Isaiah
E.A.S. wrote:
... MS-50 VCO PCB


Oh?
Randy
Mike, thanks for checking in! I'd bet there are times you really do think about buying a bar on a beach in the tropics. I know it's crossed my mind more than a few times.

Randy
E.A.S.
OH, Hello friend!! This is fun!

NOISE/SH/LFO 2.0 PCB by itsfatmike, on Flickr

I'll be packaging these up tonight.

(BTW, I've ordered extras!)



-Mike
MUFF WIGGLER Forum Index -> Music Tech DIY Goto page 1, 2, 3, 4  Next [all]
Page 1 of 4
Powered by phpBB © phpBB Group